Table of Contents
Advertisement
List of Functions
This section describes the overview of each function to be set and set values that can be registered in user
types.
• About default "HOST" function
You can operate this by the setting value specified in RIP software.
When you set to other than "HOST", it operates by that setting value, not by the instruction from RIP
software.
Depending on RIP software, there are some functions that cannot be instructed by software. In such a
case, it operates by the setting value of "When no instruction from RIP exists".
• For the specifying method with the RIP software, refer to the operation manual of the RIP software.
Function name
FEED COMP. (
P.2-33)
DROP. POS CORRECT
(
P.2-35)
LOGICAL SEEK(
P.3-3)
INK LAYERS (
P.3-10)
DRYING TIME (
P.3-3)
LEFT
MARGIN
(
P.3-6)
RIGHT
REFRESH (
)
P.3-10
FEED SPEED (
P.3-10)
MAPS
PRINT SPEED
(
P.3-5)
ADJUST
Belt Encoder
(
P.3-5)
OFF, PAGE,
LENGTH, TIME
PAGE
INTERVAL 1 to 1000 page
AUTO
TYPE
CLEANING
LENGTH INTERVAL 0.1 to100.0m
(
P.3-8)
TYPE
TIME INTERVAL 10 to 120 min
TYPE
INTERVAL WIPING (
P.3-9)
HEAD GAP (
P.2-22
)
*1. This is the setting value to be used for printing when setting value is not specified at the RIP software (host) side, or, you give priority
to the setting value at the machine side, even if you set "Host" to the type registration of this machine.
*2. When you set this to "100%" or more, required time for completion of printing will be shortened. However, enough drying time cannot
be ensured and it may affect the image quality.
*3. The initial value is "Separated (20.0 mm), SOFT" only during Sb300 filling.
3-2
Set value
Default
-9999 ~ 0 ~ 9999
0
-40.0 ~ 0 ~ 40.0
0
HOST / ON / OFF
HOST
HOST /1 ~ 9
HOST
HOST /0.0 ~ 9.9 sec
HOST
HOST / -10 ~ 85mm
HOST
(1mm unit)
HOST / -10 ~ 85mm
HOST
(1mm unit)
HOST / Lv.0 (Refresh
interval long) ~ 3 (Refresh
HOST
interval short)
*2
HOST / 10 ~ 200%
HOST
OFF/ON
OFF
-50 to +50%
0%
OFF/ON
OFF
OFF
1 page
NORMAL / SOFT / HARD
SOFT
0.5m
NORMAL / SOFT / HARD
SOFT
10 min
NORMAL / SOFT / HARD
SOFT
3 to 255 minutes
, OFF
OFF
1.5 to 7.0mm
2.0 mm
When no instruction
*1
from RIP exists
Used
correcting a media-feeding rate and
correct it.
Used to adjust the dot position in go
and return printing.
Sets the scan movable area during
ON
printing.
Sets the number of layers in which
1
ink is to be applied.
0 sec
Sets the drying time of ink per scan.
0 mm
Sets a non-printing area along the
right and left edges of the media.
0 mm
Refreshes the print heads during
Lv.3
printing.
Changes the media feeding speed
100%
in printing.
Perform setting to reduce stripes
between passes.
Set this to ON when you notice
the uneven feeding or the joints of
the belt.
*3
Sets
operation for the head performed
before printing or during printing.
Sets the wiping operation during
printing.
Sets the head gap.
Outline
to
print
a
pattern
for
the
automatic
cleaning
Advertisement
Table of Contents
