Table of Contents
Advertisement
Message
< L OC A L >
P O S I T I V E P R E S S U R E
< L OC A L >
N E G A T I V E P . A D J U S T
< L OC A L >
I N K N E A R E N D
[ E N T ]
< L OC A L >
E X P I R A T I ON
[ E N T ]
< L OC A L >
E X P I R A T I ON ( 1 M )
[ E N T ]
< L OC A L >
E X P I R A T I ON ( 2 M )
[ E N T ]
< L OC A L >
S U P P L Y
I N K
: 1 2 3 4 5 6 7 8
< L OC A L >
S u b t a n k S e n s : 1 2 3 4 5 6 7 8
< L OC A L >
I n k O v e r f l o w : 1 2 3 4 5 6 7 8
< L OC A L >
T A N K l e v r l H
: 1 2 3 4 5 6 7 8
< L OC A L >
T A N K l e v r l L
: 1 2 3 4 5 6 7 8
< L OC A L >
R e p l a c e D e A i r M o d u l e
< L OC A L >
M a c h i n e T EMP / H i
* * * ° C
< L OC A L >
* * * ° C
M a c h i n e T EMP / L o
< L OC A L >
Ym o t o r C l e a n i n g [ MN T ]
< L OC A L >
R e p l a c e Ym o t o r
B r u s h
Cause
The value of the positive pressure sen-
sor is abnormal.
Pressure needs to be adjusted.
The ink of the ink bottle has been
nearly used up.
The specified expiration date of an ink
bottle has passed.
The expiration date of an ink bottle has
passed (one month has passed after
the specified expiration date).
The expiration date of an ink bottle has
passed (two months have passed after
the specified expiration date).
Ink could not be supplied to the sub
tank.
The liquid level sensor abnormality of
the sub tank has been detected.
Overflow from the sub tank has been
detected.
Though a certain amount was con-
sumed, there is no change in the sub
tank sensor High.
Though a certain amount was con-
sumed, there is no change in the sub
tank sensor Low.
The deaeration module in the ink path
shall be replaced soon.
(One year has passed since you
started using it.)
The machine temperature is high.
The machine temperature is low.
Time to clean the Y motor has come.
Time to replace the brush of Y motor
has come.
Warning / Error Messages
Solution
• Perform "PRESSURE ADJUST" (
the maintenance. If you cannot adjust it to the
normal value, or, even if you perform, it may be
displayed, contact your local distributor to call
for service.
• Press the
key to check the relevant
ink bottle. Be careful because it may be INK
NEAR END soon.
The expiration date has passed.
However, you can use it until the end of the fol-
lowing month.
• One month has passed after the expiration
date.
However, you can use it until the end of this
month. (The ink bottle lamp blinks in red.)
Two months have passed after the expiration
date.
Replace the ink bottle generating the warning
with a new one.
• Perform "SUB TANK" (
P.5-5) of the mainte-
nance. Also check the remaining amount of ink in
the ink bottle. Even if you performed this, when
the message is displayed, contact your local dis-
tributor to call for service.
• Turn off the power to the machine and turn it on
after a while.
• If the same error message appears again, contact
your local distributor to call for service.
• Perform "SUB TANK" (
tenance. Even if you performed this, when the
message is displayed, contact your local dis-
tributor to call for service.
• The deaeration module shall be replaced.
Contact a distributor in your district, our office,
or our call center.
• Adjust the ambient temperature of the installa-
tion place.
(20 °C to 30 °C (68°F?86°F))
• Turn off the power and vacuum debris of the Y
motor from the vacuuming window.
• After the replacement, press the
on the local screen to clear the warning.
• The brush of Y motor shall be replaced.
Contact a distributor in your district, our office,
or our call center.
P.5-8) of
1
1
1
P.5-6) of the main-
1
5
(
P.4-25)
MAINT.
key
5-13
Advertisement
Table of Contents
