Table of Contents
Advertisement
Message
E R ROR 3 0 5
U S B T I ME OU T
E R ROR 4 0 1
MO T OR X
E R ROR 4 0 2
MO T OR Y
E R ROR 4 0 3
X C U R R E N T
E R ROR 4 0 4
Y C U R R E N T
E R ROR 4 4 d
S T A T I ON P O S E R ROR
E R ROR 5 0 5
ME D I A J AM
E R ROR 5 0 c
ME D I A W I D T H S E N S OR
E R ROR 5 0 c
ME D I A W I D T H S E N S OR
E R ROR 5 0 9
HDC POS CN T
E R ROR 5 0 a
Y OR I G I N
E R ROR 5 0 f
L - S C A L E B L A C K
E R ROR 5 1 9
N E G A T I V E P . S E N S OR
E R ROR 5 1 a
P O S I T I V E P . S E N S OR
E R ROR 6 1 7
S U B T A N K S N N : 1 2 3 4 5 6 7 8
E R ROR 6 1 8
T A N K l e v e l H
: 1 2 3 4 5 6 7 8
E R ROR 6 1 9
T A N K l e v e l L
: 1 2 3 4 5 6 7 8
E R ROR 6 1 a
O V E R F L OW
: 1 2 3 4 5 6 7 8
E R ROR 6 1 b
S U P P L Y
I N K
: 1 2 3 4 5 6 7 8
Cause
Occurrence of a time out error on a
USB device.
An excessive load was applied to the X
motor.
An excessive load was applied to the Y
motor.
An error due to an excessive current of
the X motor was detected.
An error due to an excessive current of
the Y motor was detected.
An error occurred in the station posi-
tion.
The media jam occurs.
The media width has not been detected
correctly.
The media width has not been detected
correctly.
A HDC position counter error occurred.
Y-origin could not be detected.
Abnormal linear scale.
The value of the negative pressure
sensor is abnormal.
The value of the positive pressure sen-
sor is abnormal.
The liquid level sensor abnormality of
the sub tank has been detected.
Though a certain amount was con-
sumed, there is no change in the sub
tank sensor High.
Though a certain amount was con-
sumed, there is no change in the sub
tank sensor Low.
Overflow from the sub tank has been
detected.
Ink could not be supplied to the sub
tank.
Warning / Error Messages
Solution
• Turn off the main power to the machine and
turn it on after a while.
If the same error message appears again, con-
tact your local distributor to call for service.
• Remove the media and reset it.
• Check the media set position. (
• Clean the media sensor. (
• Check the media set position. (
• Turn off the main power to the machine and
turn it on after a while.
If the same error message appears again, con-
tact your local distributor to call for service.
• Perform "PRESSURE ADJUST" (
the maintenance. If you cannot adjust it to the
normal value, or, even if you perform, it may be
displayed, contact your local distributor to call
for service.
• Turn off the main power to the machine and
turn it on after a while.
If the same error message appears again, con-
tact your local distributor to call for service.
• Perform "SUB TANK" (
tenance. Even if you performed this, when the
message is displayed, contact your local dis-
tributor to call for service.
• Perform "SUB TANK" (
tenance. Also check the remaining amount of
ink in the ink bottle. Even if you performed this,
when the message is displayed, contact your
local distributor to call for service.
1
P.2-20)
1
P.4-3)
P.2-20)
1
P.5-8) of
1
5
P.5-5) of the main-
P.5-5) of the main-
5-17
Advertisement
Table of Contents
