Mitsubishi Electric MELSEC iQ-R Series User Manual page 554

Error Error
code (System/
(Hexad axis/axes
ecimal) group)
3403H System
3404H System
3405H System
3406H System
3407H System
3408H System
3409H System
340AH System
340BH System
340DH System
340EH System
340FH System
3410H System
3411H System
3412H System
3413H System
3414H System
22 TROUBLESHOOTING
552
22.5 List of Error Codes
Error name Error detail and cause
Out of Master Axis No. • The value is out of range for
Range master axis No.
• Invalid axis No. has been set.
Out of Slave Axis No. • The value is out of range for
Range slave axis No.
• Invalid axis No. has been set.
Out of Master Axis 1 • The value is out of range for
No. Range axis No. of master axis 1.
• Invalid axis No. has been set.
Out of Master Axis 2 • The value is out of range for
No. Range axis No. of master axis 2.
• Invalid axis No. has been set.
Out of Latch Count The value is out of range for
Range RatchCount.
Latch Count Incorrect RecordCount has not been set
when
RecodeMode=RecordCount,Ring
Buffer.
Out of Touch Probe ID The value is out of range for
Range TouchProbeID.
Out of Lower Limit The value is out of range for
Position Range FirstPosition.
Out of Upper Limit The value is out of range for
Position Range LastPosition.
Out of Compensation The value is out of range for
Time Range CompensationTime.
Out of Latch Mode The value is out of range for
Range RatchMode.
No Calculation Profile The calculation profile does not
exist.
Calculation Profile The value is out of range for Data
Incorrect or Version.
Calculation Profile The operation was executed
Operating during calculation profile
operating.
Calculation Profile Error The calculation profile is broken,
or the format is incorrect.
Out of Offset Range Offset exceeds the number of
elements of calculation profile
(file or open area).
Out of Calculation The value is out of range for
Profile ID Range ProfileData.ID.Number.
Detection Operation at
timing (At error
start/ occurrence
during
control
At startWhen Not execute FB.
executing FB
At startWhen Not execute FB.
executing FB
At start Not execute FB.
When
executing FB
At start Not execute FB.
When
executing FB
When Not execute FB.
executing FB
When Not execute FB.
executing FB
When Not execute FB.
executing FB
When Not execute FB.
executing FB
When Not execute FB.
executing FB
When Not execute FB.
executing FB
When Not execute FB.
executing FB
During The execution of FB is
operation interrupted.
During The execution of FB is
operation interrupted.
During The execution of FB is
operation interrupted.
During The execution of FB is
operation interrupted.
During The execution of FB is
operation interrupted.
At start • [At start] The FB is not
During executed.
operation • [During operation]
Operates with
previous setting value.
Remedy
• Set the value within
the range of 1 to
65535.
• Set the axis No. in
which instance is
created.
• Set the value within
the range of 1 to
65535.
• Set the axis No. in
which instance is
created.
• Set the value within
the range of 1 to
65535.
• Set the axis No. in
which instance is
created.
• Set the value within
the range of 1 to
65535.
• Set the axis No. in
which instance is
created.
Set the value within the
range.
Set RecordCount.
Set the valid touch probe
ID.
Set the value within the
range for probe data.
Set the value within the
range for probe data.
Set the value within the
range of -5.0 to 5.0 [s].
Set the value within the
range for
MC_RECORD_MODE.
Set the existing
calculation profile.
Set the data within the
range.
Operate it when Busy of
FB is FALSE.
Set the calculation
profile for a correct
format.
Set a value which does
not exceed the number
of elements of
calculation profile (file
and open area) in Offset.
Set a value within the
range for
ProfileData.ID.Number.