O2: Hoa Keypad Functions - YASKAWA Z1000 User Manual

No.
(Addr. Name
Hex)
Frequency Reference
o1-15
and Frequency Related
(3107)
Monitor Custom Units 3
o1-16 F1 Key Function
(3108) Selection
o1-17 F2 Key Function
(3109) Selection
o1-18 User Defined Parameter
(310A) Upper
o1-19 User Defined Parameter
(310B) Lower
<1> Default setting is dependent on parameter o1-03, HOA Keypad Display Selection.
u

o2: HOA Keypad Functions

No.
(Addr. Name
Hex)
OFF Key Function
o2-02
Selection
(506)
o2-03 User Parameter Default
(507) Value
o2-04
Drive Model Selection
(508)
Frequency Reference
o2-05
Setting Method
(509)
Selection
Operation Selection
o2-06
when HOA Keypad is
(50A)
Disconnected
Motor Direction at
o2-07
Power Up when Using
(527)
Operator
o2-19 Selection of Parameter
(61F) Write during Uv
YASKAWA TOEP YAIZ1U 03B YASKAWA AC Drive – Z1000 User Manual
LCD Display
Sets the customer-specified unit display for the frequency
Fref Cust Unit 3 reference parameters and frequency related monitors when
o1-03 = 3 and o1-09 = 15 as custom units
Selects the function of the F1 key and the LCD display text
F1 Key Func Sel
above the F1 key.
0: Standard
0: Standard
1: Mon
1: Monitor
2: DRV/BYP
2: Drive/Bypass (DRV/BYP)
3: RUN BYP
3: Bypass Run Command (RUN BYP)
4: RLY
4: Toggle Relay Output (RLY)
Selects the function of the F2 key and the LCD display text
F2 Key Func Sel
above the F2 key.
0: Standard
0: Standard
1: Mon
1: Monitor
2: DRV/BYP
2: Drive/Bypass (DRV/BYP)
3: RUN BYP
3: Bypass Run Command (RUN BYP)
4: RLY
4: Toggle Relay Output (RLY)
Allows the user to set values that can be used as reference
Userdefined par1
information.
Allows the user to set values that can be used as reference
Userdefined par2
information.
LCD Display
Oper STOP Key 0: Disabled. OFF key is disabled in REMOTE operation.
0: Disabled 1: Enabled. OFF key is always enabled.
1: Enabled
0: No change.
User Default Sel
1: Set defaults. Saves parameter settings as default values for a
0: No Change
User Initialization.
1: Save User Init
2: Clear all. Clears the default settings that have been saved for
2: Clear User Init
a User Initialization.
Enter the drive model. Setting required only if installing a new
Inverter Model # control board.
Oper Ref Method 0: ENTER key must be pressed to enter a frequency reference.
0: Disabled 1: ENTER key is not required. The frequency reference can be
1: Enabled adjusted using the up and down arrow keys only.
Oper Discon Det 0: The drive continues operating if the HOA keypad is
0: Disabled disconnected.
1: Enabled 1: An oPr fault is triggered and the motor coasts to stop.
0: Forward
For/RevSel@PwrUp
1: Reverse
0: Forward
This parameter requires assigning drive operation to the HOA
1: Reverse
keypad.
Selects whether parameter settings can be changed during a DC
ParameterSet Sel bus undervoltage condition. Used with 24 V Power Supply (PS-
0: Disabled A10L, PS-A10H).
1: Enabled 0: Disabled
1: Enabled
B.10 o: Operator-Related Settings
Description
Description
Values Page
Default: 41
183
Range: 30 to 7A
Default: 0
183
Range: 0 to 4
Default: 0
183
Range: 0 to 4
Default: 0
183
Range: 0 to 999
Default: 0
183
Range: 0 to 999
Values Page
Default: 1
184
Range: 0, 1
Default: 0
135
Range: 0 to 2
Default:
Determined by 184
drive capacity
Default: 0
135
Range: 0, 1
Default: 1
184
Range: 0, 1
Default: 0
185
Range: 0, 1
Default: 0
–
Range: 0, 1
B
307