YASKAWA Z1000 User Manual page 377

Overload Protection ............................................................ 262
Overtorque Detection 1 ........................................................ 210
Overvoltage...................................................................... 211
Overvoltage 2 ................................................................... 211
Overvoltage Protection......................................................... 262
ov Suppression Function Selection........................................... 300
P
Parameter Access Level........................................................ 146
Parameter Range Setting Error................................................ 225
Parameter Selection Error ..................................................... 227
Parameter Settings .............................................................. 109
Parameters to Minimize Motor Hunting and Oscillation .................. 195
PASS ............................................................................. 223
Password ......................................................................... 147
Password Settings............................................................... 147
Peak Hold Current .............................................................. 321
Peak Hold Output Frequency ................................................. 321
Permanent Magnet Motor Control............................................ 116
PF ................................................................................. 212
Phase Order Selection .......................................................... 152
PI Accel/Decel Time ........................................................... 159
PID Feedback Loss ....................................................... 204, 219
PI Feedback...................................................................... 322
PI Feedback Function Selection .............................................. 161
PI Feedback High Detection Level ........................................... 162
PI Feedback High Detection Time ........................................... 162
PI Feedback Loss Detection Selection ....................................... 158
PI Feedback Low Detection Level ........................................... 158
PI Feedback Low Detection Time ............................................ 159
PI Feedback Offset ............................................................. 161
PI Function Setting ............................................................. 156
PI Input (feedback) ............................................................. 322
PI Input Limit ................................................................... 161
PI Maximum Boost Time...................................................... 161
PI Monitors ...................................................................... 189
PI Offset Adjustment ........................................................... 157
PI Output......................................................................... 322
PI Output 2 Monitor Max Upper/Lower 4 Digits .......................... 163
PI Output 2 Monitor Minimum ............................................... 163
PI Output Fault .................................................................. 240
PI Output Gain Setting ......................................................... 157
PI Output Level Selection ..................................................... 157
PI Output Limit ................................................................. 157
PI Output Lower Limit......................................................... 161
PI Output Monitor Calculation Method...................................... 163
PI Output Reverse Selection .................................................. 157
PI Primary Delay Time Constant ............................................. 157
PI Setpoint ....................................................................... 322
PI Setpoint Boost Setting ...................................................... 160
PI Setpoint Display Digits ..................................................... 162
PI Setpoint Monitor Unit Selection........................................... 163
PI Setpoint Scaling ............................................................. 160
PI Setpoint Selection ........................................................... 159
PI Setpoint User Display....................................................... 162
PI Setpoint Value ............................................................... 159
PI Sleep Delay Time ........................................................... 159
PI Sleep Function Start Level ................................................. 159
PI Sleep Input Source .......................................................... 160
PI Snooze Deactivation Level................................................. 160
YASKAWA TOEP YAIZ1U 03B YASKAWA AC Drive – Z1000 User Manual
PI Snooze Delay Time ......................................................... 160
PI Snooze Feedback Level .................................................... 161
PI Snooze Level................................................................. 160
PI Square Root Gain............................................................ 161
PI Unit Selection ................................................................ 162
PM Motor Auto-Tuning Mode Selection .................................... 141
PM Motor Base Frequency .................................................... 142
PM Motor d-Axis Inductance ................................................. 142
PM Motor Induced Voltage Constant ........................................ 143
PM Motor Parameter Settings................................................. 137
PM Motor q-Axis Inductance ................................................. 143
PM Motor Rated Current ...................................................... 142
PM Motor Rated Power........................................................ 142
PM Motor Rated Voltage ...................................................... 142
PM Motor Stator Resistance .................................................. 142
PM Motor Type ................................................................. 142
Powering Up the Drive......................................................... 117
Power Ratings (Three-Phase 600 V Class).................................. 258
Preparing the Ends of Shielded Cables ..................................... 0
Present Value Access........................................................... 336
Previous Fault ................................................................... 318
Programming Errors............................................................ 225
Programming Mode ...................................................... 106, 109
Proportional Gain Setting (P) ................................................. 156
Protective Cover ..................................................................40
Protective Covers, Reattaching .................................................77
Protective Covers, Removing .............................................. 76, 77
Protective cover to prevent miswiring .........................................33
Pull-In Current .................................................................. 305
Pull-In Current Compensation Time Constant.............................. 305
Pull-In Current Level for PM Motor Tuning................................ 143
Pump (Secondary) Application ............................................... 120
Pump with PI Control Application .......................................... 120
R
R-....................................................................................87
R+ ...................................................................................87
Radiated and Radio Frequency Noise........................................ 255
Rated Current Depending on Carrier Frequency ........................... 264
Rated Current Setting Alarm .................................................. 229
Rated Slip Error ................................................................. 230
rdEr ............................................................................... 232
READ ............................................................................ 185
rEAd .............................................................................. 232
Reading BACnet Drive Parameters .......................................... 341
Reading Parameter Settings ................................................... 232
Real Time Clock Setting................................................. 108, 187
Reattaching the Front Cover ....................................................78
Reattaching the HOA Keypad ..................................................78
Reattaching the Protective Cover...............................................79
Reattaching the Terminal Cover ........................................... 76, 77
Removing the Front Cover ......................................................78
Removing the HOA Keypad ....................................................78
Removing the Protective Cover.................................................79
Removing the Terminal Cover............................................. 76, 77
RESET Key...................................................................... 101
Resistance Tuning Error ....................................................... 229
Response Messages from Drive to Master .................................. 335
Return Fan with PI Control Application..................................... 119
Reverse Operation Selection .................................................. 152
Index
377