YASKAWA Z1000 User Manual page 378

Index
Reverse Operation Selection 2 by PI Output................................ 164
rF .................................................................................. 212
rH ................................................................................. 212
Rotational Auto-Tuning for V/f Control..................................... 136
rr................................................................................... 212
RS-485 Interface ................................................................ 329
RTS Control Selection ................................................... 173, 331
Rubber Bushing ...................................................................28
Run Command/Frequency Reference Source Selection Error............ 226
Run Command at Power Up................................................... 152
Run Command Method Selection ...................................... 174, 332
Run Command Selection ...................................................... 236
RUN Command Selection for AUTO mode ................................ 272
Run Command Selection for AUTO Mode ................................. 123
Run Command Source Selection ............................................. 322
S
S- ....................................................................................87
S: Special Parameters .......................................................... 309
S+ ...................................................................................87
S1 ...................................................................................86
S1: Dynamic Noise Control Function........................................ 309
S2 ...................................................................................86
S2: Sequence Timers ........................................................... 309
S3 ...................................................................................86
S4 ...................................................................................86
S5 ...................................................................................86
S6 ...................................................................................86
S7 ...................................................................................86
SC .............................................................................86, 213
S-Curve Characteristics .................................................. 164, 195
SE ................................................................................. 223
Secondary PI Disable Mode................................................... 312
Secondary PI Display Digits .................................................. 311
Secondary PI Enable Selection ............................................... 311
Secondary PI Feedback Detection Selection ................................ 313
Secondary PI High Feedback Detection Time .............................. 313
Secondary PI High Feedback Level .......................................... 312
Secondary PI Integral Limit Setting.......................................... 312
Secondary PI Integral Time Setting .......................................... 312
Secondary PI Low Feedback Detection Level .............................. 312
Secondary PI Low Feedback Detection Time .............................. 312
Secondary PI Output Level Selection ........................................ 312
Secondary PI Output Lower Limit ........................................... 312
Secondary PI Output Upper Limit............................................ 312
Secondary PI Proportional Gain Setting ..................................... 312
Secondary PI Setpoint Value.................................................. 312
Secondary PI Unit Selection .................................................. 312
Secondary PI User Display .................................................... 311
Second Line Monitor Selection ............................................... 182
Selecting the Type of Auto-Tuning .......................................... 138
Selection of Parameter Write during Uv..................................... 307
Self-Diagnostics................................................................. 343
Sequence Timer 1 Day Selection ............................................. 309
Sequence Timer 1 Reference Source......................................... 309
Sequence Timer 1 Selection................................................... 309
Sequence Timer 1 Start Time ................................................. 309
Sequence Timer 1 Stop Time ................................................. 309
Sequence Timer 2 Day Selection ............................................. 310
Sequence Timer 2 Reference Source......................................... 310
378
Sequence Timer 2 Selection................................................... 310
Sequence Timer 2 Start Time ................................................. 310
Sequence Timer 2 Stop Time ................................................. 310
Sequence Timer 3 Day Selection ............................................. 310
Sequence Timer 3 Reference Source......................................... 311
Sequence Timer 3 Selection................................................... 310
Sequence Timer 3 Start Time ................................................. 310
Sequence Timer 3 Stop Time ................................................. 310
Sequence Timer 4 Day Selection ............................................. 311
Sequence Timer 4 Reference Source......................................... 311
Sequence Timer 4 Selection................................................... 311
Sequence Timer 4 Start Time ................................................. 311
Sequence Timer 4 Stop Time ................................................. 311
Sequence Timer Error .......................................................... 228
SEr ................................................................................ 213
Serial Comms Cable Connection Terminal ................................. 328
Serial Communication Terminals...............................................87
Serial Communication Transmission Error ................................. 217
Set Time.............................................................. 108, 187, 308
Setup Group ..................................................................... 111
Setup Group Parameters ....................................................... 112
Setup Mode ...................................................................... 109
Shielded Twisted-Pair Cables ................................................ 0
Side-by-Side Installation.........................................................39
Side-by-Side Setup ...............................................................39
Simple Motor Setup Using V/f Control...................................... 115
Simplified Setup Using the Setup Group .................................... 109
Sinking/Sourcing Mode for Digital Inputs ....................................92
SN...................................................................................86
Soft Charge Bypass Relay Maintenance..................................... 321
Soft Charge Bypass Relay Maintenance Time.............................. 221
Soft CLA Selection ............................................................. 303
Soft Starter Speed Reference at Previous Fault............................. 319
Software Current Limit Selection ............................................ 179
Software No. (Flash) ........................................................... 318
Software No. (ROM) ........................................................... 318
Software version ..................................................................25
Space Between Drives (Side-by-Side Mounting) ............................39
Speed Agreement Detection Level ........................................... 301
Speed Agreement Detection Level (+/-) ..................................... 301
Speed Agreement Detection Width .......................................... 301
Speed Agreement Detection Width (+/-) .................................... 301
Speed Control Range ........................................................... 261
Speed Feedback Detection Control Gain .................................... 305
Speed Response ................................................................. 261
Speed Search Deactivation Current .......................................... 154
Speed Search Deceleration Time ............................................. 154
Speed Search Delay Time ..................................................... 155
Speed Search Detection Compensation Gain ............................... 155
Speed Search Method Selection .............................................. 156
Speed Search Restart Current Level.......................................... 155
Speed Search Restart Detection Time........................................ 155
Speed Search Selection at Start ............................................... 154
Speed Search Wait Time....................................................... 156
Stall Prevention ................................................................. 195
Stall Prevention Level during Acceleration ................................. 299
Stall Prevention Level during Run ........................................... 300
Stall Prevention Limit during Acceleration ................................. 299
Stall Prevention Selection during Acceleration............................. 299
Stall Prevention Selection during Deceleration............................. 299
YASKAWA TOEP YAIZ1U 03B YASKAWA AC Drive – Z1000 User Manual