Table of Contents
Advertisement
A
B
Check for an open or short circuit between
J 8709 and
P/J8728
are OK.
Y
N
Repair the open or short circuit.
Measure the voltage between Finisher PWB P/J8709-3 (+) and GND (-). The voltage is
approx. +5VDC.
Y
N
Go to
Integrated Finisher Wirenets
Measure the voltage between Finisher PWB P/J8709-2 (+) and GND (-). Actuate the
Compiler Exit Sensor. The voltage normally changes.
Y
N
Replace the Compiler Exit Sensor
Check the wires and connectors for an intermittent open or short circuit. If the problem
continues, replace the Finisher PWB
Enter [012-095]. The Finisher Transport Motor rotates.
Y
N
Check the connections of
P/J8706
and P/J8739.
connected.
Y
N
Connect
P/J8706
and
P/J8739
Check for an open or short circuit between
P/J8706
and
P/J8739
are OK.
Y
N
Repair the open or short circuit.
Measure the voltage between Finisher PWB P/J8706-5 (+) and GND (-), and P/J8706-7
(+) and GND (-). Each voltage is approx. +24VDC.
Y
N
Go to
Integrated Finisher Wirenets
Check the wires and connectors for an intermittent open or short circuit. If the problem
continues, replace the Finisher Transport Motor
the Finisher PWB
(PL
22.7).
Check the wires and connectors for an intermittent open or short circuit. If the problem contin-
ues, replace the Finisher PWB
(PL
22.7).
Status Indicator RAPs
012-152 (Integrated Finisher), 012-161 (Integrated Fin-
P/J8709
and P/J8728. The wires between
and check the +5VDC circuit.
(PL
22.5).
(PL
22.7).
P/J8706
and
P/J8739
are securely
securely.
P/J8706
and P/J8739. The wire between
and check the +24VDC circuit.
(PL
22.4). If the problem persists, replace
BUS Updated 12/2011
012-161 (Integrated Finisher) Set Eject Jam RAP
BSD-ON:
BSD 12.6 - Integrated Finisher Set Eject (1 of 2)
In the Eject Motor's ejecting operation, Eject Home Sensor ON was detected within a specified
time after the start of the reverse operation of the Eject Motor.
(The Eject Motor should have ejected paper, but returned Home earlier than specified.)
Initial Actions
•
Check the Eject Home Sensor is properly installed, not broken, and has no foreign object.
•
Power Off/On.
Procedure
Check the specifications of paper. Paper is in spec.
Y
N
Replace the paper with new paper that is in spec.
Check the condition of the paper. The paper is in normal condition without any problem
that causes the paper to be bent or caught.
Y
N
Resolve any problem that causes the paper to be bent or caught.
Check the Eject mechanism for deformed parts, broken parts, and/or belt damage. The Eject
mechanism free from defects.
Y
N
Repair the Eject mechanism.
Enter
Component Control
[012-252]. Block and unblock the Eject Home Sensor with a piece of
paper. The display changes.
Y
N
Check the connections of
P/J8700
connected.
Y
N
Connect
P/J8700
and
P/J8725
Check for an open or short circuit between
P/J8700
and
P/J8725
are OK.
Y
N
Repair the open or short circuit.
Measure the voltage between Finisher PWB P/J8700-9 (+) and GND (-). The voltage is
approx. +5VDC.
Y
N
Go to
Integrated Finisher Wirenets
Measure the voltage between Finisher PWB P/J8700-2 (+) and GND (-). Block and
unblock the Eject Home Sensor with a piece of paper. The voltage changes.
Y
N
Replace the Eject Home Sensor
A
B
07/2011
2-90
and P/J8725.
P/J8700
and
P/J8725
are securely
securely.
P/J8700
and P/J8725. The wires between
and check the +5VDC circuit.
(PL
22.10).
Initial Issue
WorkCentre 5335 Family Service Documentation
Advertisement
Table of Contents
