Table of Contents
Advertisement
Y
N
Check the connections of
P/J8707
and P/J8722.
connected.
Y
N
Connect
P/J8707
and
P/J8722
Check for an open or short circuit between
P/J8707
and
P/J8722
are OK.
Y
N
Repair the open or short circuit.
Measure the voltage between Finisher PWB P/J8707-6 (+) and GND (-). The voltage is
approx. +5VDC.
Y
N
Go to
Integrated Finisher Wirenets
Measure the voltage between Finisher PWB P/J8707-5 (+) and (-). Block and unblock the
Stacker Stack Sensor 1 by rotating the actuator. The voltage changes.
Y
N
Replace the Stacker Stack Sensor 1
Check the wires and connectors for an intermittent open or short circuit. If the problem
continues, replace the Finisher PWB
Enter [012-279]. Block and unblock the Stacker Stack Sensor 2 by rotating the actuator. The
display changes.
Y
N
Check the connections of
P/J8707
and P/J8721.
connected.
Y
N
Connect
P/J8707
and
P/J8721
Check for an open or short circuit between
P/J8707
and
P/J8721
are OK.
Y
N
Repair the open or short circuit.
Measure the voltage between Finisher PWB P/J8707-3 (+) and GND (-). The voltage is
approx. +5VDC.
Y
N
Go to
Integrated Finisher Wirenets
Measure the voltage between Finisher PWB P/J8707-2 (+) and GND (-). Block and
unblock the Stacker Stack Sensor 2 by rotating the actuator. The voltage changes.
Y
N
Replace the Stacker Stack Sensor 2
Check the wires and connectors for an intermittent open or short circuit. If the problem
continues, replace the Finisher PWB
Enter [012-060] and [012-061] alternately. The Stacker Motor rotates.
Status Indicator RAPs
012-211 (Integrated Finisher)
P/J8707
and
P/J8722
are securely
securely.
P/J8707
and P/J8722. The wires between
and check the +5VDC circuit.
(PL
22.8).
(PL
22.7).
P/J8707
and
P/J8721
are securely
securely.
P/J8707
and P/J8721. The wires between
and check the +5VDC circuit.
(PL
22.8).
(PL
22.7).
BUS Updated 12/2011
Y
N
Check the connections of
P/J8711
connected.
Y
N
Connect
P/J8711
and
P/J8736
Check for an open or short circuit between
J8711
and P8736 are OK.
Y
N
Repair the open or short circuit.
Enter [012-060], measure the voltage between Finisher PWB P/J8711-1 (+) and GND (-
). The voltage changes.
Y
N
Go to
Integrated Finisher Wirenets
continues, replace the Finisher PWB
Enter [012-061], measure the voltage between Finisher PWB P/J8711-2 (+) and GND (-
). The voltage changes.
Y
N
Go to
Integrated Finisher Wirenets
continues, replace the Finisher PWB
Check the wires and connectors for an intermittent open and short circuit. If the problem
continues, replace the Stacker Motor
Check the wires and connectors for an intermittent open or short circuit. If the problem contin-
ues, replace the Finisher PWB
(PL
07/2011
2-92
and P/J8736.
P/J8711
and
P/J8736
securely.
P/J8711
and P8736. The wires between
and check the +24VDC circuit. If the problem
(PL
22.7).
and check the +24VDC circuit. If the problem
(PL
22.7).
(PL
22.8).
22.7).
WorkCentre 5335 Family Service Documentation
are securely
P/
Initial Issue
Advertisement
Table of Contents
