Panasonic DBS-576 Technical Manual page 66

FF1: System Programming
FF1 0 03 (00-15) 48 Hold (0 or 1) Hold
Introduction
FF1 0 03 (00-15) 49 Hold (0 or 1) Hold
FF1 0 03 (00-15) 50 Hold (0 or 1) Hold
FF1 0 04: Trunk COS Definitions
0
System
FF1 0 04 (00-15) 01 Hold (0 or 1) Hold
Configuration
FF1 0 04 (00-15) 02 Hold (0 or 1) Hold
FF1 0 04 (00-15) 03 Hold (0 or 1) Hold
FF1 FF1 0 04 (00-15) 04 Hold (0 or 1) Hold
FF1 0 04 (00-15) 05 Hold (0 or 1) Hold
System
FF1 0 04 (00-15) 06 Hold (0 or 1) Hold
FF1 0 05: Serial Ports
FF2 FF1 0 05 0001 Hold (0-7) Hold
Trunks
FF1 0 05 0002 Hold (0-5) Hold
FF1 0 05 0003 Hold (0-2) Hold
FF1 0 05 0004 Hold (0 or 1) Hold
FF3
FF1 0 05 0005 Hold (1-255) Hold
Extensions
FF1 0 05 0017 Hold (0-7) Hold
FF1 0 05 0018 Hold (0-5) Hold
FF4
FF1 0 05 0019 Hold (0-2) Hold
FF-/Soft Keys
FF1 0 05 0020 Hold (0 or 1) Hold
FF1 0 05 0021 Hold (1-255) Hold
FF1 0 05 0033 Hold (0-7) Hold
FF5
FF1 0 05 0034 Hold (0-5) Hold
Groups
FF1 0 05 0035 Hold (0-2) Hold
FF1 0 05 0036 Hold (0 or 1) Hold
FF1 0 05 0037 Hold (1-255) Hold
FF6
FF1 0 06: Serial Port Output Data
TRS/ARS
FF1 0 06 0001 Hold (0-2) Hold
FF1 0 06 0002 Hold (0-2) Hold
FF1 0 06 0003 Hold (0-2) Hold
FF7
FF1 0 06 0004 Hold
Applications
FF1 0 06 0005 Hold (0-2) Hold
FF1 0 07 and 08: PBX Parameters
FF1 0 07 (0001-0012) Hold (0-16) Hold
FF8
Maintenance
FF1 0 08 (0001-0006) Hold FLASH (0-
9999) Hold
FF1 0 09: SMDR Output Format
FF1 0 09 0001 Hold (0-2) Hold
FF1 0 10 and 11: Call Restriction Between COS
Appendix A
FF1 0 10 (00-15) (01-16) Hold (0 or 1) Hold Call Restriction Between Extension COS
FF1 0 11 (00-15) (01-16) Hold (0 or 1) Hold Call Restriction Between Trunk COS
Appendix B
Page 1-4
Extension COS: OHVA
Extension COS: OHVA Answer
Extension COS: Call-Waiting Answer at
HOLD
Trunk COS: Incoming Ring Tone Source
Trunk COS: Dial Tone to Tie-Line
Trunk COS: Forced Recovery at Fast-Busy 0 (Enabled)
Trunk COS: DID/DNIS Table
Trunk COS: Paging on DISA/Tie-Line Call
Trunk COS: DISA ID Verification
Serial Port 1: Data Format
Serial Port 1: Baud Rate
Serial Port 1: Protocol
Serial Port 1: Echo Control (future use)
Serial Port 1: Maximum Input Digits (future
use)
RAI Serial Port: Data Format
RAI Serial Port: Baud Rate
RAI Serial Port: Protocol
RAI Serial Port: Echo Control
RAI Serial Port: Maximum Input Digits
Serial Port 2: Data Format
Serial Port 2: Baud Rate
Serial Port 2: Protocol
Serial Port 2: Echo Control
Serial Port 2: Maximum Input Digits
SMDR Data to Serial Port
Fault Alarm Data to Serial Port
Programmed Data to Serial Port
Not Used
Bus Monitor Data to Serial Port
Auto Pause Position Behind PBX
PBX Trunk Access Codes
SMDR Output Format
DBS 576 (USA) issued 05/20/98
Section 400-Programming
0 (Allowed) 1-72
0 (Allowed) 1-73
1 (Not Allowed) 1-74
1-75
0 (use trunk's 1-75
Ring Pattern)
1 (Enabled) 1-76
1-77
0 ("A" side) 1-77
0 (Not Allowed) 1-78
0 (Verify) 1-79
1-80
5 (8bits/NoPar./ 1-80
1stop)
5 (9600 bps) 1-81
0 (No order) 1-81
0 (Off) 1-82
80 digits 1-82
5 (8Bits/NoPar./ 1-83
1stop)
5 (9600 bps) 1-83
0 (No order) 1-84
0 (Off) 1-84
1 digit 1-85
5 (8bits/NoPar./ 1-85
1stop)
5 (9600 bps) 1-86
0 (No order) 1-86
0 (Off) 1-87
80 digits 1-87
1-88
1 (Port 1) 1-88
0 (None) 1-88
2 (Port 2) 1-89
-- 1-89
2 (Port 2) 1-90
1-91
1 (for "9") 1-91
0 (for all others)
Code 1: 9 1-92
Codes 2-6: none
1-93
1 (Format #1) 1-93
1-94
0 (Allowed) 1-94
0 (Allowed) 1-95
576-13-400
Introduction
0
System
Configuration
FF1
System
FF2
Trunks
FF3
Extensions
FF4
FF-/Soft Keys
FF5
Groups
FF6
TRS/ARS
FF7
Applications
FF8
Maintenance
Appendix A
Appendix B