Control change #93 can be used to control the Send 1
level, and #91 to control the Send 2, and modify their
respective settings. These messages will be received on
the MIDI channel speciﬁed for each timbre in the 3.1:
Ed–Param1, MIDI page.
The actual send levels are determined by summing this
value with the send level "S1 (Send1(MFX)), " "S2
(Send2(MFX))" (PROG 7.1–2a) for each oscillator of the
program selected for the timbre.
■ 7.1–1b: UTILITY
☞"Write Combination," "Solo Selected Timbre" (1.1–1c)
For details on how to select the desired utility function, refer
to "PROG 1.1–1c: UTILITY."
Copy Insert Effect
☞ PROG 7.1–1c
However, the MIDI control channel speciﬁed for "Control
Channel" of the 7.1: Ed–InsertFX, Setup page will not be
DKit IFX Patch (DrumKit IFX Patch)
This command changes the "BUS Select" settings for each
key of the drum kit, so that connections to the IFX are tem-
porarily changed to L/R. This can be executed only if the
program speciﬁed for a timbre is a drum program, and the
"BUS Select" (7.1–1a) setting is DKit, and the "BUS Select"
(GLOBAL 5.1–3a) for each key of the drum kit is IFX.
1 Select "DKit IFX Patch" to access the dialog box.
2 At the right of "DrumKit IFX→," select L/R as the patch
3 To execute Drum Kit Insert Effect Patch, press the [F8]
("OK") key. To cancel without executing, press the [F7]
To return the drum kit to its original state, execute IFX →
Here you can select the type of insert effect, turn it on/off
7.1–2a: Ed-InsertFX Setup
These parameters are the same as in Program mode.
( ☞ PROG 7.1–2)
However, dynamic modulation (Dmod) of the insert effect
and the "Pan (CC#8), "Send1(MFX1)," and "Send2(MFX2)"
that follow the insert effect will be controlled on the "Con-
trol Channel" (7.1–2b) MIDI channel, unlike in Program
mode. The control changes used are the same as in Program
7.1–2b: Control Channel
Speciﬁes the MIDI channel on which dynamic modula-
tion (Dmod) of the insert effect and the "Pan (CC#8),
"Send1(MFX1)," and "Send2(MFX2)" that follow the
insert effect will be controlled.
The channel number of the timbre routed through this IFX
will be followed by a "*" displayed at the right of Ch01–16.
If two or more timbres with different MIDI channel settings
are routed through the IFX, this parameter speciﬁes which
of these channels will be used to control the effect.
G ch: The global MIDI channel "MIDI Channel" (GLOBAL
2.1–1a) will be used to control the effect. Normally you will
set this to G ch.
All Rt. (All Routed): The channel of any timbre routed
through this effect can be used to control the effect. (Chan-
nels of each routed timbre will be indicated by "*".)
If "BUS Select" (7.1–1a) is set to DKit for a timbre for
which a drums program is selected, the MIDI channel
of that timbre will be valid only if this is set to All Rt.,
regardless of the drum kit "BUS Select" setting (GLO-
BAL 5.1–3a) or the Utility "DrumKit IFX Patch" (7.1–
[L/R, 1, 2, 1/2, Off]
[Ch01...16, G ch, All Rt.]