2: Arp. A (Arpeggiator A); 3: Arp. B (Arpeggiator B) - Korg TR Parameter Manual

Example 2)
The "MIDI Channel" (3.1–1a) of timbres 1, 2, 3, 4, and 5
are set respectively to Gch, Gch, 02, Gch, and 03. Their
"Status" (3.1–1a) is set respectively to INT, Off, INT, Off,
and INT. Assign arpeggiator A to timbres 2 and 3, assign
arpeggiator B to timbres 4 and 5, and check "Arpeggiator
Run A, B" (1.1–4a/5a, 6.1–1a).
• When the front panel [ARP ON/OFF] key is off, playing
the keyboard will sound only timbre 1. (Timbres 2 and 4
are receiving the Gch, but they will not sound since their
"Status" is Off.)
• When you turn on the front panel [ARP ON/OFF] key,
arpeggiator A will operate for timbres 2 and 3, and
arpeggiator B will operate independently for timbres 4
and 5. (Arpeggiators A and B are triggered by receiving
note data on any MIDI channel of an assigned timbre,
but in this example they are being triggered from the
Gch.)
When you play the keyboard, arpeggiator A will operate
for timbres 2 and 3, but only timbre 3 whose "Status" is
INT will sound. Similarly, arpeggiator B will operate for
timbres 4 and 5, but only timbre 5 whose "Status" is INT
will sound.
In this way, you can make settings so that a timbre does
not sound when the arpeggiator is off, but sounds only
when the arpeggiator is on.
Arpeggiator Pattern - A
Trigger
= Gch, Ch2 A
Pattern - B
Arpeggiator
Trigger
B
= Gch, Ch3
■ 6.1–1c: UTILITY
☞"Write Combination," "Solo Selected Timbre" (1.1–1c)
For details on how to select the desired utility function, refer
to "PROG 1.1–1c: UTILITY."
Copy Arpeggiator
This command copies arpeggiator settings.
1 Select "Copy Arpeggiator" to access the dialog box.
2 In "From" select the copy source (mode, bank, number)
arpeggiator.
If you are copying from Combination, or Song, select
either A or B to if you wish to copy settings from only
one arpeggiator, or select A&B if you wish to copy the
settings of both arpeggiators.
3 If you are copying from a Program, or are copying either
A or B from Combination, or Song, select either A or B as
the "To" copy destination.
4 To execute the Copy Arpeggiator command, press the
[F8] ("OK") key. To cancel without executing, press the
[F7] ("Cancel") key.
44
Arpeggiator
Assign
Off
Timbre 1 MIDI Ch=Gch Status=INT
A
Timbre 2 MIDI Ch=Gch Status=Off
A Timbre 3 MIDI Ch=2ch Status=INT
B
Timbre 4 MIDI Ch=Gch Status=Off
B
Timbre 5 MIDI Ch=3ch Status=INT
6.1–2: Arp. A
6.1–3: Arp. B
The Arp. A pages you make settings for arpeggiator A. The
Arp. B pages you make settings for arpeggiator B.
You can also use Utility "Copy Arpeggiator" (6.1–1c) to
copy settings from another mode such as Program
mode.
6.1–2a
6.1–2(3)a: Arpeggiator-A(B) Setup
Pattern*
Octave*
Reso (Resolution)*
Gate
Velocity
Sounded by normal
Swing
keyboard playing
Does not sound
Sort*
Pattern - A
Latch*
Does not sound
Pattern - B
Key Sync.*
Keyboard*
These parameters are the arpeggiator A settings for the com-
bination.
(☞p.24 PROG 6.1: Ed–Arp.)
* These parameters can also be set in "1.1–4: Arp. A, 1.1–5:
Arp. B"
6.1–2(3)b:
(Tempo)
☞1.1–1a
■ 6.1–2(3)c: UTILITY
☞"Write Combination," "Solo Selected Timbre" (1.1–1c),
"Copy Arpeggiator" (6.1–1c)
(Arpeggiator A)
(Arpeggiator B)
[P000...P004, U000(INT)...U215(User)]
[ , ,
[000...100%, Step]
[001...127, Key, Step]
(Tempo)
6.1–2b
6.1–2c
[1, 2, 3, 4]
, , , ]
[–100...+100%]
[Off, On]
[Off, On]
[Off, On]
[Off, On]
[040...240, EXT]