KORG TR Parameter Manual: Mix (mixer)

Music workstation.
Hide thumbs
1.1–3: Mix
(Mixer)
Here you can set the pan and volume for each timbre 1–8.
1.1–3a
1.1–3a: Pan, Volume
Pan
Sets the pan for each timbre 1–8. (This parameter can also be
set from the Mixer page of 2.1: Ed-Prog/Mix.)
L001...C064...R127: A setting of L001 is far left and R127 is
far right. A setting of C064 will reproduce the pan setting
that was made for the oscillator in Program mode.
OSC1
OSC2
OSC1: Amp1 Pan=L001
OSC2: Amp2 Pan=R127
Left
Center
Right
Pan (CC#10)
C064
L032
L001
R096
R127
Left
Center
Right
OSC1
OSC2
OSC1: Amp1 Pan=C064
OSC2: Amp2 Pan=C064
Left
Center
Right
Pan (CC#10)
C064
L032
L001
R096
R127
Left
Center
Right
If a mono-type insertion effect is inserted, the setting you
make here will be ignored. In this case, the "Pan (CC#8)"
parameter in 7.1: Ed–InsertFX, Setup page will adjust the
panning of the sound after the insertion effect (☞p.162 "3.
Mixer").
RND: The oscillator pan will change randomly at each note-
on.
If "Status" (3.1–1a) has been set to INT, MIDI control
change #10 (panpot) messages can be received to con-
trol the setting. CC#10 values of 0 or 1 will place the
sound at far left, 64 at center, and 127 at far right.
Pan can be controlled by messages received on the
"MIDI Channel" (3.1–1a).
34
1.1–3b
[RND, L001...C064...R127]
OSC1: Amp1 Pan=L032
OSC2: Amp2 Pan=R096
Left
Center
Right
Pan (CC#10)
C064
L032
L001
R096
R127
Left
Center
Right
Volume
Adjusts the volume of each timbre 1–8. (This parameter can
also be set from the Mixer page of 2.1: Ed-Prog/Mix.)
The volume of each timbre is determined by summing
this volume value with the MIDI volume (CC#7) and
expression (CC#11). If "Status" (3.1–1a) has been set to
INT, incoming MIDI CC#7 or CC#1 1 messages will con-
trol the volume of a timbre. (However these messages
will not affect the setting of this parameter.)
If "Status" is EXT or EX2, the value of this parameter
will be transmitted as MIDI CC#7 when the combina-
tion is changed. However this will not be transmitted
by a timbre that is set to the same MIDI channel as the
global MIDI channel. This message is transmitted on
the "MIDI Channel" (3.1–1a) specified for each timbre.
■ 1.1–3b: UTILITY
☞"Write Combination," "Solo Selected Timbre" (1.1–1c),
"Select by Category" (1.1–1c, PROG 1.1–1a)
For details on how to select the desired utility function, refer
to "PROG 1.1–1c: UTILITY."
Hold Balance
Adjusts the volume of the Combi while preserving the vol-
ume balance between timbres 1–8.
Selects the "Volume" of any timbre, select "Hold Balance"
from the Utility menu, and press the [F8] ("OK") key. A
check mark will appear at the left of "Hold Balance." (The
upper right of the LCD screen will indicate [Hold Bal.]) In
this state, adjusting any "Volume" value will simulta-
neously change the volume of the other timbres as well,
while preserving the volume balance between timbres 1–8.
[000...127]

Advertising

   Also See for KORG TR

   Related Manuals for KORG TR

   Related Content for KORG TR

Comments to this Manuals

Symbols: 0
Latest comments: