3: Foot - Korg TR Parameter Manual

LCD Contrast
This sets the contrast of the LCD screen.
Higher values will increase the contrast.
If because of the temperature or other reasons, the LCD
screen is unreadable when the power is turned on, use
the following procedure to adjust the contrast.
1 Press the [EXIT] key three times, and then press the
[GLOBAL] key.
2 Hold down the [EXIT] key, and press the [REC/WRITE]
key.
3 Use the [VALUE] dial to adjust the setting.
1.1–2b: Memory Protect
This setting also applies to Load Preload/Demo Data
(1.1–1d). Loading will not be possible if protect is speci-
fied for even one of the types of data selected for load-
ing in "Kind" (☞p.125).
Program
This setting protects the internal program memory.
On (checked): Internal program memory will be protected,
and the following write operations cannot be performed.
• Writing a program
• Receiving program data via MIDI data dump
• Loading program data from SD card
Off (unchecked): Data can be written to internal program
memory.
Combi (Combination)
This setting protects the internal combination memory.
On (checked): Internal combination memory will be pro-
tected, and the following write operations cannot be per-
formed.
• Writing a combination
• Receiving combination data via MIDI data dump
• Loading combination data from SD card
Off (unchecked): Data can be written to internal combina-
tion memory.
Song
This setting protects the internal song memory.
However, when the power is turned off, the song data in
song memory will be lost regardless of this setting.
On (checked): Internal song memory will be protected, and
the following write operations cannot be performed.
• Recording to the sequencer
• Receiving song data via MIDI data dump
• Loading song data from SD card
• Saving template songs in Sequencer mode
Off (unchecked): Data can be written to internal song mem-
ory.
[0...62] Drum Kit
This setting protects the internal drum kit memory.
On (checked): Internal drum kit memory will be protected,
and the following write operations cannot be performed.
• Writing a drum kit
• Receiving drum kit data via MIDI data dump
• Loading drum kit data from SD card
Off (unchecked): Data can be written to internal drum kit
memory.
Arp. UsrPat (Arp. User Pattern)
This setting protects the internal user arpeggio pattern
memory.
On (checked): Internal user arpeggio pattern memory will
be protected, and the following write operations cannot be
performed.
• Writing a user arpeggio pattern
• Receiving user arpeggio pattern data via MIDI data
[Off, On]
dump
• Loading user arpeggio pattern data from SD card
Off (unchecked): Data can be written to internal user arpeg-
gio pattern memory.
■ 1.1–2c: UTILITY
☞"Write Global Setting," "Load Preload/Demo data,"
"Change all bank references," "Half Damper Calibration,"
"After Touch Calibration" (1.1–1d)
[Off, On]
1.1–3: Foot
Specify the polarity and function of a switch or pedal con-
nected to the rear panel.
1.1–3a
[Off, On]
1.1–3a: Damper/Assignable Foot Switch, Pedal
Foot SW Assign
Select the function that will be controlled by a pedal switch
(PS-1 option [sold separately]) connected to the rear panel
ASSIGNABLE SWITCH jack (☞p.226 "Foot Switch Assign
List").
Foot Pedal Assign
Indicates the function that will be controlled by a foot vol-
ume pedal (XVP-10 or EXP-2 option [sold separately]) con-
nected to the rear panel ASSIGNABLE PEDAL jack (☞p.227
"Foot Pedal Assign List").
[Off, On]
[Off, On]
1.1–3b
[Off...Tap Tempo]
[Off...Knob4]
127