Prog 7.1: Ed-Inserfx; 1: Bus - Korg TR Parameter Manual

PROG 7.1: Ed–InserFX
☞For details on insertion effect, refer to p.159 "7. Effect
Guide."
7.1–1: BUS
These settings specify the bus on which the output of the
oscillator will be sent, and adjust the send levels to the mas-
ter effects.
The following diagram shows the LCD screen when "Mode
(Oscillator Mode)" (2.1–1a) is set to Single or Double.
7.1–1a
7.1–1a: BUS
BUS Select:
BUS Select (All OSCs)
Specifies the bus to which oscillators 1 and 2 will be sent.
If this is set to 1/2, the oscillator pan settings (5.1–1b,
5.2–1) will be used to output the sound in stereo from
AUDIO OUTPUT (INDIVIDUAL) 1/2. When the oscil-
lator pan is controlled by CC#10 (pan) or AMS (Alter-
nate Modulation Source), the sound will be output with
the pan setting that is in effect at note-on. Unlike the
case when this is set to L/R to output the sound from
(MAIN) L/MONO and R, the pan of a sounding note
will not change in real-time.
If you wish to adjust the pan in real-time while playing
a note and output the sound from AUDIO OUTPUT
(INDIVIDUAL) 1/2, set "BUS Select" to IFX, set "IFX"
to 00: No Effect, and set the "BUS Select" (7.1–2a) after
passing through IFX to 1/2.
MFX Send:
OSC1 Send1
Sets the volume (send level) at which the output of OSC1
will be sent to master effect 1. This is valid when "BUS
Select" is set to L/R or Off.
If "BUS Select" is set to IFX, the send levels to master effect 1
and 2 are set by "S1 (Send1(MFX1))" and "S2
(Send2(MFX2))" (7.1–2a) after passing through IFX of the
Setup page.
OSC1 Send2
Sets the volume (send level) at which the output of OSC1
will be sent to master effect 2 ( ☞ "OSC1 Send1").
OSC2 Send1
OSC2 Send2
Sets the volume (send level) at which the output of OSC2
will be sent to master effects 1 and 2. These parameters will
be valid when "Mode (Oscillator Mode)" (2.1–1a) is set to
Double and "BUS Select" is set to L/R or Off (☞"OSC1
Send1").
26
7.1–1c
[L/R, IFX, 1, 2, 1/2, Off]
[000...127]
[000...127]
[000...127]
[000...127]
CC#93 will control the Send 1 level for OSC 1 and 2,
and control change #91 will control the Send 2 level for
OSC 1 and 2. These are controlled on the global MIDI
channel "MIDI Channel" (GLOBAL 2.1–1a).
The actual send level is determined by summing these
values with the send level setting of each oscillator.
7.1–1b: Use DKit Setting
The LCD screen shown below is for when "Mode (Oscillator
Mode)" (2.1–1a) is set to Drums.
7.1–1b
Use DKit Setting
This will be available when "Mode (Oscillator Mode)" is set
to Drums.
On (checked): The "BUS (BUS Select)" (GLOBAL 5.1–3a)
setting for each key of the selected drum kit will be used.
Check this when you want to apply an insert effect to an
individual drum instrument, or to output an individual
drum instrument to one of the AUDIO OUTPUT (INDIVID-
UAL) jacks.
If the "Mode (Oscillator Mode)" is Single or Double, this
setting has no effect.
Off (unchecked): The setting of the "BUS Select," "MFX
Send" (7.1–1a) parameter described below will be used. All
drum instruments will be sent to the specified bus.
■ 7.1–1c: UTILITY
☞"Write Program" (1.1–1c)
For details on how to select the desired utility function, refer
to "PROG 1.1–1c: UTILITY."
Copy Insert Effect
This command copies effect settings from Program, Combi-
nation, Song, or Sampling mode (if the EXB-SMPL option is
installed).
1 Select "Copy Insert Effect" to access the dialog box.
2 In "From" select the copy source mode, bank, and num-
ber.
You can use the Bank [A]–[GM] keys to select the bank.
3 Select the effect that you wish to copy. You can also copy
from a master effect.
If you are copying from a master effect, the result may
not be identical, due to differences in the routing and
level settings of a master effect.
7.1–1c
[Off, On]