26: St.biphasemod (Stereo Biphase Modulation); 27: St.vibrato (Stereo Vibrato) - Korg TR Parameter Manual

Music workstation
Hide thumbs Also See for TR:
Table of Contents

Advertisement

26: St.BiphaseMod
(Stereo Biphase Modulation)
This stereo chorus effect adds two different LFOs together.
You can set the Frequency and Depth parameters for each
LFO individually. Depending on the setting of these LFOs,
very complex waveforms will create an analog-type, unstable
modulated sound.
Stereo In - Stereo Out
Left
Chorus/Flanger
Chorus/Flanger
Right
LFO1: Tri / Sine
LFO2: Tri / Sine
LFO1 Wave (LFO1 Waveform)
a
Selects LFO1 waveform
LFO2 Wave (LFO2 Waveform)
b
Selects LFO2 waveform
LFO Phase Sw
c
Switches the LFO phase difference between left and right
F1 (LFO1 Frequency)
Sets the LFO1 speed
(Source)
d
Selects the modulation source of LFO1&2 speed
(Amount)
Sets the modulation amount of LFO1 speed
F2 (LFO2 Frequency)
Sets the LFO2 speed
e
(Amount)
Sets the modulation amount of LFO2 speed
L Dly (L Pre Delay)
Sets the delay time for the left channel
f
R Dly (R Pre Delay)
Sets the delay time for the right channel
Depth1
Sets the depth of LFO1 modulation
(Source)
g
Selects the modulation source of LFO1&2 modulation depth
(Amount)
Sets the modulation amount of LFO1 modulation depth
Depth2
Sets the depth of LFO2 modulation
h
(Amount)
Sets the modulation amount of LFO2 modulation depth
Feedback
Sets the feedback amount
i
HiDamp (High Damp)
Sets the damping amount in the high range
W/D (Wet/Dly)
Sets the balance between the effect and dry sounds
j
(Source)
Selects the modulation source of the effect balance
(Amount)
Sets the modulation amount of the effect balance
LFO1
LFO2
182
High Damp
Feedback
High Damp
180 [degree]
Triangle, Sine
Triangle, Sine
0, 180degree
0.02...30.00Hz
Off...Tempo
–30.00...+30.00
0.02...30.00Hz
–30.00...+30.00
0.0...50.0ms
0.0...50.0ms
Off...Tempo
–100...+100
–100...+100
–100...+100
–Wet...–1:99, Dry, 1:99...Wet
Fx:10,
Off...Tempo
–100...+100
Bi-Phase Modulation LFO
Depth1
+
Depth2
27: St.Vibrato
(Stereo Vibrato)
This effect causes the pitch of the input signal to shimmer.
Using the AutoFade allows you to increase or decrease the
shimmering speed.
Stereo In - Stereo Out
Left
Wet / Dry
Right
LFO: Tri / Sine
AutoFade
Wet / Dry
LFO Wave (LFO Waveform)
Selects LFO Waveform
a
Shape (LFO Shape)
Determines how much the LFO waveform is changed
LFO Freq Mod (LFO Frequency Mod)
b
Switches between Dmod and AUTOFADE for the LFO frequency
modulation
Freq (LFO Frequency)
Sets the LFO speed
(Source)
c
Selects the modulation source of LFO speed
(Amount)
Sets the modulation amount of LFO speed
BPM/MIDI Sync
Switches between using the frequency of the LFO speed and using
the tempo and notes
BPM
Selects MIDI Clock and assigns tempo
d
Base (Base Note)
Selects the type of notes that specify the LFO speed
Fx:16
Times
Sets the number of notes that specify the LFO speed
Fx:16
Depth
0...100
Sets the depth of LFO modulation
(Source)
e
Selects the modulation source of the LFO modulation depth
(Amount)
Sets the modulation amount of the LFO modulation depth
AUTOFADE Src (AUTOFADE Source)
f
0...100
Selects the modulation source that starts AutoFade
Fade Rate (Fade-In Rate)
Sets the rate of fade-in
g
Dly (Fade-In Delay)
Sets the fade-in delay time
Fx:17
W/D (Wet/Dly)
0...100%
Sets the balance between the effect and dry sounds
(Source)
h
Selects the modulation source of the effect balance
(Amount)
Sets the modulation amount of the effect balance
b: LFO Freq Mod, f: AUTOFADE Src, g: Fade Rate, g: Dly
When "LFO Freq Mod" is set to AUTOFADE, you can use the
modulation source selected in "AUTO FADE Src" as a trigger to
automatically fade in the modulation amount. When "BPM/MIDI
Sync" is set to On, you cannot use this.
The "Fade Rate" parameter specifies the rate of fade-in. The "Dly"
parameter determines the time from AutoFade modulation source
ON until the fade-in starts.
The following is an example of fade-in where the LFO speed is
increased from "1.0Hz" to "4.0Hz" when a note-on message is
received.
"AUTOFADE Src"=Gate1, "Freq"=1.00 Hz
Vibrato
Vibrato
LFO Shape
Fade-In Delay
LFO Frequency
Dmod, AUTOFADE
Dry, 1:99...99:1, Wet
Wet / Dry
Wet / Dry
Triangle, Sine
–100...+100
Fx:20
0.02...20.00Hz
Fx:09,
Off...Tempo
–20.00...+20.00Hz
Off, On
Fx:09,
MIDI, 40...240
Fx:09
Fx:09
1...16
Fx:09
0...100
Off...Tempo
–100...+100
Off...Tempo
,
1...100
00...2000ms
Off...Tempo
–100...+100

Hide quick links:

Advertisement

Table of Contents
loading

Table of Contents