KORG TR Parameter Manual: Midi Transmission When The Tr's Controllers Are Operated

Music workstation.
Hide thumbs
MIDI transmission when
the TR's controllers are operated
The following table shows the relation between the MIDI
messages that are transmitted when the TR's controllers are
operated, and the AMS (alternate modulation source) or
DMS (dynamic modulation source) that correspond to each
MIDI message. # indicates a fixed function, and * indicates
an assignable function.
When one of the TR's controllers is operated, the corre-
sponding or the assigned control change will be transmitted.
Pitch Bend messages will be transmitted only when the joy-
stick is moved in the X (horizontal) direction. The operation
in each mode is described below. (Explanations are given
only for control changes, but the same applies to pitch bend
as well.)
Program mode
When one of the TR's controllers is operated, a control
change message will be transmitted on the global MIDI
channel.
If a REALTIME CONTROLS B-mode knob [1]–[4] is set
to Master Volume, the universal exclusive message
Master Volume will be transmitted.
Combination mode
When one of the TR's controllers is operated, a control
change message will be transmitted on the global MIDI
channel.
Simultaneously, the message will also be transmitted on the
MIDI channel ("MIDI Channel" COMBI 3.1–1a) of any tim-
bre whose "Status" (COMBI 3.1–1a) is EXT or EX2.
When one of the TR's controllers is operated, its effect will
apply to any timbre whose "Status" is INT and whose
"MIDI Channel" setting is either Gch or the same as the glo-
bal MIDI channel.
In the case of Master Volume, the universal exclusive
message Master Volume will be transmitted only on the
global MIDI channel.
You can make settings for MIDI Filter (COMBI 4.1–4.4)
to enable or disable control changes and controllers for
each timbre. When checked, the above operations will
be enabled.
Effect dynamic modulation can be controlled when the
"Control Ch (Control Channel)" (COMBI 7.1–1b, 7.2–1a, 7.2–
1c) setting for IFX, MFX1, 2, or MEQ is either set to Gch or to
the same channel as the global MIDI channel. (In the case of
All Rt., control is possible on the MIDI channel of any
routed timbre.)
228
Sequencer mode
When one of the TR's controllers is operated, its effect will
apply to the track 1–16 that is selected by "Track Select"
(SEQ 1.1–1c).
If the "Status" (SEQ 3.1–1a/2a) of the track selected by
"Track Select" is EXT, EX2, or BTH, a control change mes-
sage will be transmitted on the MIDI channel specified by
"MIDI Channel" (SEQ 3.1–1a/2a).
If the "Status" is INT or BTH, operating one of the TR's con-
trollers will affect only that track. Simultaneously, the same
effect will also apply to any track with the same "MIDI
Channel" setting.
In the case of Master Volume, the universal exclusive
message Master Volume will be transmitted.
You can make settings for MIDI Filter (SEQ 4.1–4.4) to
enable or disable control changes and controllers for
each track. When checked, the operations effective for a
"Status" of INT or BTH will be enabled. Tracks whose
"Status" is EXT, EX2, or BTH will transmit control
changes regardless of this setting.
Effect dynamic modulation can be controlled when the
"Control Ch (Control Channel)" (SEQ 7.1–1b, 7.2–1a, 7.2–1c)
setting for IFX, MFX1, 2, or MEQ matches the MIDI channel
of the track selected by "Track Select." (In the case of All Rt.,
control is possible on the MIDI channel of all routed tracks.)
If one of the TR's controllers is operated during realtime
recording, the corresponding or assigned control change
will be recorded.
Sampling mode
When one of the TR's controllers is operated, a control
change message will be transmitted on the global MIDI
channel ("MIDI Channel" GLOBAL 2.1–1a).
In the case of Master Volume, the universal exclusive
message Master Volume will be transmitted.
It is not possible to make AMS settings in Sampling
mode.
* Global MIDI channel:
GLOBAL 2.1: MIDI "MIDI Channel" (2.1–1a)

Advertising

   Also See for KORG TR

   Related Manuals for KORG TR

Comments to this Manuals

Symbols: 0
Latest comments: