■ 7.1–1(2)b: UTILITY
☞"Memory Status," "Solo Selected Track" (1.1–1d), "DKit
IFX Patch" (COMBI 7.1–1b), "FF/REW Speed," "Set Loca-
For details on how to select the desired utility function, refer
to "PROG 1.1–1c: UTILITY."
Copy Insert Effect
☞ PROG 7.1–1c
However, the MIDI control channel speciﬁed in "Control
Channel" of the 7.1: Insert FX, Setup page will not be copied.
Here you can select the type of the insert effects, turn them
7.1–3a: Insert FX Setup
These parameters are the same as in Program mode.
However, this differs from Program mode in that insert
effect dynamic modulation (Dmod) and the "Pan (CC#8),"
"Send1(MFX1)," and "Send2(MFX2)" which follow the
insert effect are controlled on the MIDI channel speciﬁed by
"Control Channel" (7.1–1b). The control changes used are
the same as in Program mode.
The pan (CC#8) and Send 1 and 2 that you specify here are
used when playing or recording from the beginning of the
song. If you change these settings while recording, the set-
tings will be recorded as musical data, and during playback,
the settings will change accordingly. You can also change
these settings during playback. However if Pan (CC#8) and
Send 1/2 data has already been recorded, the settings will
change according to the recorded data.
If the "Status" (3.1–1(2)a) is INT or BTH, receiving
CC#8, #93, or #91 will cause the post- insert ef fect pan
and send 1/2 to be controlled, changing the settings.
When you change songs or return to the beginning of
the song, tracks whose "Status" is BTH, EXT, or EX2
will transmit these settings on the MIDI channel speci-
ﬁed by "Control Channel."
7.1–3b: Control Channel
An asterisk "*" will be displayed at the right of the channel
number Ch01–16 for tracks that are routed to an IFX. If mul-
tiple tracks with differing MIDI channel settings are routed,
these channels specify the channel that will be used to con-
trol the effect.
All Rt. (All Routed): Control can be performed from any of
the MIDI channels of the tracks that are routed.
7.1–3c: Routing Map, BUS Select
This displays the settings of the insert effect. The routing,
speciﬁed effect name, and on/off status of the insert effect
T01...16: BUS Sel
While viewing the map, you can specify the bus where the
program oscillators for each track 1–16 will be sent.
Use the cursor keys to select the track, and use the [INC]/
[DEC] keys or the [VALUE] dial to set "BUS Select" (7.1–
This setting can also be made in "BUS Select" (7.1–3a).
■ 7.1–3d: UTILITY
[L/R, 1, 2, 1/2, Off]
☞"Memory Status," "Solo Selected Track" (1.1–1d), "Copy
Indicates the MIDI channel that will control effect
dynamic modulation (Dmod), pan following the insert
effect "Pan (CC#8)," "Send1(MFX1)," and
If "BUS Select" (7.1–1(2)a) is set to DKit for a track in
which a drum program is selected, the MIDI channel of
that track will be valid only if this is set to All Rt.,
regardless of the drum kit "BUS (BUS Select)" (GLO-
BAL 5.1–3a) setting or the utility setting "DrumKit IFX
[DKit, L/R, IFX, 1, 2, 1/2, Off]
Insert Effect," (PROG 7.1–1c, 7.1–1b/2b), "DKit IFX
Patch" (COMBI 7.1–1b), "FF/REW Speed," "Set Location"
(1.1–1d), "Select by Category" (PROG 7.1–2c)
[Ch01...16, All Rt.]