KORG TR Parameter Manual Page 137

Music workstation.
Hide thumbs

Advertisement

This means that the Velocity Curve, After Touch Curve, and
Transpose settings will affect the data that is transmitted
from MIDI OUT when this instrument's keyboard is played,
and the data that is recorded on the internal sequencer. MIDI
data received from MIDI IN or the data played back by the
internal sequencer will not be affected.
Transpose
Note number
change
PostMIDI: Velocity Curve, After Touch Curve, and Trans-
pose will be applied to data before it enters the tone genera-
tor.
This means that the Velocity Curve, After Touch Curve, and
Transpose settings will affect the data that is sent to the
internal tone generator when you play this instrument's
keyboard, when the internal sequencer is played back, or
when data is received from MIDI IN.
This setting will not affect the data that is transmitted from
MIDI OUT or recorded on the internal sequencer when you
play this instrument's keyboard or playback the sequencer.
Record
Local Control On
On (checked) Local Control On: The keyboard, joystick,
REALTIME CONTROLS knobs [1]–[4], [SW1], and [SW2]
keys of this instrument will controls its internal tone genera-
tor.
Off (unchecked) Local Control Off: The keyboard, joystick,
and REALTIME CONTROLS knobs [1]–[4] etc. of this instru-
ment will be disconnected from the internal tone generator.
This means that operating this instrument (using the key-
board or joystick to perform, or playing the sequencer) will
not produce sound.
Uncheck this setting if the echo-back from an external
sequencer causes this instrument to sound in duplicate.
Even if this is unchecked, MIDI transmission and recep-
tion will occur as usual. Note messages will be trans-
mitted when you play the keyboard, and this
instrument's tone generator will sound when note mes-
sages are received.
Local
control
130
MIDI IN
Velocity
Curve
Play
Record
Sequencer
Aftertouch
Curve
Scale
MIDI OUT
MIDI IN
Velocity
Curve
Play
Sequencer
Aftertouch
Curve
Scale
Transpose
Pitch change
MIDI OUT
Sequencer Arpeggiator
OFF
Record
Trigger
ON
MIDI IN
MIDI OUT
2.1–1b: MIDI Filter
Enable Program Change
On (checked): Program changes will be transmitted and
received.
In Program mode (PROG 1.1: Play), the program will be
switched when a program change message is received on
the global MIDI channel specified by "MIDI Channel" (2.1–
1a). When you switch programs, a program change message
will be transmitted on the global MIDI channel.
In Combination mode (COMBI 1.1: Play), the combination
Tone
generator
will be switched when a program change message is
received on the global MIDI channel. However, it is possible
to set the "Combi (Combi Change)" parameter so that the
combination is not switched. When a program change is
received on the channel specified for each timbre by "MIDI
Channel" (COMBI 3.1–1a), the program of that timbre will
be switched. However, the program changes for each timbre
will be affected by the setting of the "Program Change"
parameter (COMBI 4.1–1a).
When you switch combinations, a program change message
will be transmitted on the global MIDI channel, and also
transmitted simultaneously on the channel of timbres whose
"Status" (COMBI 3.1–1a) is set to EXT or EX2.
In Sequencer mode, incoming program change messages on
a channel that corresponds to a track whose "Status" (SEQ
3.1–1(2)a) is set to INT or BTH will switch programs on that
track. When you select a song or playback song data will be
transmitted on the channels of tracks whose "Status" is set
to BTH, EXT, or EX2.
Tone
Off (unchecked): Program changes will not be transmitted
generator
or received.
Bank (Bank Change)
On (checked): The Bank Select control change message will
[Off, On]
be transmitted together with program change messages.
This is valid when "Enable Program Change" is checked.
Off (unchecked): Bank Select messages will not be transmit-
ted or received.
When recording on the internal sequencer, bank select
messages will be recorded regardless of this setting.
However for playback, this setting will apply.
Combi (Combi Change)
On (checked): When in COMBI 1.1: Play, an incoming pro-
gram change message on the global MIDI channel set by
"MIDI Channel" (2.1–1a) will switch combinations. This is
valid when "Enable Program Change" is checked. An
incoming program change on a channel other than the glo-
bal MIDI channel will switch the program of any timbre that
matches that MIDI channel.
Off (unchecked): An incoming program change message on
the global MIDI channel will switch the program of any tim-
bre whose "MIDI Channel" (COMBI 3.1–1a) matches the
global MIDI channel. The combination will not be switched.
The program changes for each timbre will be affected by the
setting of the "Program Change" parameter (COMBI 4.1–
Tone
1a).
generator
[Off, On]
[Off, On]
[Off, On]

Advertisement

   Also See for KORG TR

   Related Manuals for KORG TR

Comments to this Manuals

Symbols: 0
Latest comments: