3: Arp (Arp. Play) - Korg TR Parameter Manual

Decay (Decay Time)
This adjusts the Decay Time and Slope Time of the filter EG
and amp EG.
With an adjustment of +00, the value of the program param-
eters will be unchanged.
Positive (+) settings will lengthen the Decay Time and Slope
Time beyond the values that were set. With an adjustment of
+10, the times will be 99.
Negative (–) settings will shorten the Decay Time and Slope
Time. With an adjustment of –10, the times will be 0.
IFX Bal (IFX Balance)
This adjusts the "W/D(Wet/Dry)" setting of the insertion
effect.
With an adjustment of +00, the value of the program param-
eters will be unchanged.
Positive (+) settings will raise the Wet level above the pro-
gram setting, and lower the Dry level. With an adjustment of
+10, the setting will be "Wet" - the effected signal only.
Negative (–) settings will lower the Wet level below the pro-
gram setting, and raise the Dry level. With an adjustment of
–10, the setting will be "Dry" - the signal is unaffected.
MFX Bal (MFX Balance)
This adjusts the master effect "Rtn1 (Return1)" and "Rtn2
(Return2)" (7.2–1a) settings as a whole.
With an adjustment of +00, the value of the program param-
eters will be unchanged.
Positive (+) settings will raise the return levels above the
program setting.
With an adjustment of +10, the setting will be 127 (maxi-
mum).
Negative (–) settings will lower the return levels below the
program setting.
With an adjustment of –10, the setting will be 0.
Octave Octave of OSC 1 and 2
Stretch Transpose and Tune of OSC 1 and 2
OSC Bal High Level and Low Level of OSC1 and 2
Level Amp1 Level, Amp2 Level
Attack Amp EG Attack Time, Start Level, Attack Level,
Level Modulation S, Time Modulation A of Amp 1
and 2, and Filter EG Attack Time of Filter 1 and 2
Decay AmpEG Decay Time, Slope Time of Amp 1 and 2,
Filter EG Decay Time and Slope Time of Filter 1
and 2
IFX Bal W/D (Wet/Dry) balance of the IFX effect
MFX Bal Master Effect RTN1, 2 (Return1, 2)
■ 1.1–2c: UTILITY
☞"Write Program," "Select by Category" (1.1–1c)
4
[–10...+00...+10]
[–10...+00...+10]
[–10...+00...+10]
1.1–3: Arp
(Arp. Play)
While arpeggiator parameters are for the most part edited in
PROG 6.1: Ed-Arp., Some major parameters can be edited
here as well. When you are playing in PROG 1.1: Play, you
can edit the arpeggiator in realtime, such as changing the
arpeggio pattern etc.
You can also use the REALTIME CONTROLS C-mode
[TEMPO], [ARP-GATE], and [ARP-VELOCITY] knobs to
edit the arpeggio in realtime (☞OG p.28).
1.1–3a
1.1–3a: Arpeggiator
Pattern [P000...P004, U000(INT)...U215(User)]
Reso (Resolution)
Octave
Sort
Latch
Key Sync.
Keyboard
Make settings for the program arpeggiator ( ☞ "PROG: Ed-
Arp."). These parameters can also be set from 6.1: Ed-Arp.
setup page ( ☞ 6.1–1a).
■ 1.1–3b: UTILITY
☞"Write Program," "Select by Category" (1.1–1c)
1.1–3b
[ , , , , , ]
[1, 2, 3, 4]
[Off, On]
[Off, On]
[Off, On]
[Off, On]