Insert Effect (Ifx); In/Out; Routing - Korg TR Parameter Manual

Music workstation
Hide thumbs Also See for TR:
Table of Contents

Advertisement

The following table shows the parameters related to the
level settings:
Program mode
Input
OSC1/2 High, Low Level
Filter1/2 Trim
Amp1/2 Level
OSC1/2 Send1/2
Effect Trim parameter
Output
Effect W/D parameter
Rtn1/2 (Return1, 2)
Combination mode
Input
Volume
S1/2 (Send1/2)
Effect Trim parameter
Output
Effect W/D parameter
Rtn1/2 (Return1, 2)
Sequencer mode
Input
Volume
S1/2 (Send1/2)
Effect Trim parameter
Output
Effect W/D parameter
Rtn1/2 (Return1. 2)
Sampling mode (if the separately sold EXB-SMPL
option is installed)
Input
Rear panel AUDIO INPUT LEVEL
Input1/2 Lvl (Level)
Effect Trim parameter
Output
Effect W/D parameter
*2
Global mode
(if the separately sold EXB-SMPL
option is installed)
Input
Rear panel AUDIO INPUT LEVEL
Input1/2 (Level)
Input1/2 Send1/2
*1
:Some effects may not have these parameters.
*2
:Use this parameter to set the Audio Input Level in all
modes other than Sampling mode.
160
(PROG 2.1)
(PROG 4.1, 4.2)
(PROG 5.1, 5.2)
(PROG 7.1)
*1
(PROG 7.1, 7.2)
(PROG 7.1, 7.2)
(PROG 7.2)
(COMBI 1.1, 2.1)
(COMBI 7.1)
*1
(COMBI 7.1, 7.2)
(COMBI 7.1, 7.2)
(COMBI 7.2)
(SEQ 1.1)
(SEQ 7.1)
*1
(SEQ 7.1, 7.2)
(SEQ 7.1, 7.2)
(SEQ 7.2)
(SMPL 1.1)
*1
(SMPL 7.1)
(SMPL 7.1)
(GLOBAL 1.1)
(GLOBAL 1.1)
Insert Effect

1. In/Out

Insert Effect (IFX) have a stereo input and a stereo output.
If you select Dry (no effect) for the "W/D" parameter, the
stereo input signal will be output in stereo without being
processed by the effect. If you select Wet (effect applied), the
processed signal will be output in one of the following ways:
Mono In - Mono Out
Wet
Mono In - Stereo Out
Stereo In - Stereo Out
If you select 00: No Effect, stereo input signals are output in
stereo without being processed.
The possible routing of effect inputs and outputs is indi-
cated in the upper left corner of the block diagram.
These can be switched on/off by the "On/Off" settings in
7.1: Ed-InsertFX (or Insert FX), Setup pages IFX in each
mode. When off, the effect will be bypassed. In the same
way as for 00: No Effect, the stereo input sound will be out-
put in stereo without modification.
Separately from this "On/Off" setting, MIDI control
change CC#92 can be received to turn all IFX effect off.
A value of 0 is off, and a value of 1–127 restores the
original setting. You can also use "FX SW" (GLOBAL
1.1–1b) to turn off IFX in the same way. This is con-
trolled on the global MIDI channel "MIDI Channel"
(GLOBAL 2.1–1a).

2. Routing

2–1. Program mode
Use "BUS Select" (PROG 7.1–1a) to set the destination bus of
the oscillator output.
L/R: The signal is not sent to the Insert Effects. Instead, it is
sent to AUDIO OUTPUT (MAIN) L/MONO and R after the
Master EQ.
IFX: The signal is sent to Insert Effect IFX.
1, 2, 1/2: The signal is sent to AUDIO OUTPUT (INDIVID-
UAL) 1, 2 ( ☞ p.166 "Individual Outputs"). The signal is not
sent to the Insert Effect, Master Effects, and or Master EQ.
Off: The signal is not sent to AUDIO OUTPUT (MAIN L/
MONO, R, (INDIVIDUAL) 1 or 2. (After the Master Effects,
the signal is output to AUDIO OUTPUT (MAIN).) Select this
option if you connect the Insert Effect with the Master
Effects in series, with the send level specified by "MFX1
Send1"and "MFX2 Send2."
(IFX)
+
Effect
+
Effect
Effect
Effect

Hide quick links:

Advertisement

Table of Contents
loading

Table of Contents