Function Menu; Reverse Switch; Travel Adjust; Sub Trim - devention DEVO F12E User Handbook Manual

cleUention
DEVO F 1 2 E
Welcome to use the DEVO F12E transmitter
3.0 Function Menu
Function Menu can help you custom adjustments for the selected models. The menu includes such items
as Reverse Switch, Travel Adjust, Sub Trim, Dual Rate and Exponential, Motor Hold, Flaperon Mix, Camber
System, Differential, Balance,Gyro Sensor, Rudder to Spoiler Mix, Aileron to Rudder Mix, Elevator to Flap
Mix, Aileron to Flap Mix, Aileron to Tip Aileron Mix, Flap Rate, Brake System, Program Mix, Monitor, Fail Safe,
Sensor view, Trainer and Timer.
3.1 Reverse Switch
Reverse Switch
81
Elevator Reverse
R-Aileron Normal
L-Aileron Normal
Rudder
Normal
Motor Normal
Flap Normal
AUX2 Normal
AUX3 Normal
3.2 Travel Adjust
Reverse Switch
Elevator
Norma!
R-Aileron Normal
L-Aileron Normal
Rudder Normal
Motor Normal
Flap Normal
AUX2 Normal
AUX3 Normal
Press UP or DN to move navigation mark to ELE(take Elevator for
example), press R or L to shift the status between nomal and reverse.
These are two status for option. And the default setting is Normal. All
Channels Reverse Switch like: R-Aileron, L-Aileron, Rudde, Motor, Flap,
AUX2, AUX3, AUX4, AUX5, AUX6 and AUX7 can be referred to the way
of ELEV Reverse Switch. And press EXT to exit after finishing setting.
Press ENT to enter Main Menu; Press UP or DN to move the navigation
mark to Function Menu, and press ENT to enter Function Menu. Press
UP or DN to choose Reverse Switch and Press ENT to enter Reverse
Switch interface.
Press ENT to enter into Main Menu. Press UP or DN to move navigation mark to select item Function Menu.
Press ENT to enter Function Menu. Press UP or DN to select Travel Ajust, Press ENT to enter Travel Adjust
interface, as below illustration. It shows the Travel Adjust status of one channel:
Take Elevator for example, Press UP or DN to move navigation mark to
desired item Elevation of U. Press R or L to increase or decrease the
servo travel range. The adjustment range is from 0.0% to 150.0%. The
factory default is 100.0%.
Press UP or DN to move navigation mark to desired item Elevation of D.
Press R or L to increase or decrease the servo travel range. The adjustment
range is from 0.0% to 150.0%. The factory default is 100.0%.
Travel Adjust
g
Elevator U100.0%
D100.0%
R-Aileron
L100.0%
R100.0%
L-Aileron L100.0%
R100.0%
Rudder L100.0%
R100.0%
All other channel's Travel Adjust like R-Aileron, L-Aileron, Rudder, Motor, Flap, AUX2, AUX3, AUX4, AUX5,
AUX6 and AUX7 can be referred to Elevator travel Ajust. Press EXT to exit after setting finished.
3.3 Sub Trim
Sub Trim can move the neutral point of the servo. But we advise you to mechanically adjust the servo bell
crank if offset is far away from the neutral point of servo, because excessive usage of the sub trim may damage
the servo.
Sub Trim
Setting method:
Press ENT to enter Main Menu, Press UP or DN to move the navigation
mark to select item Function Menu. Press ENT to enter Function Menu,
Press UP or DN to select Sub trim, and press ENT to enter Sub Trim
interface.
Elevator
R-Aileron 0.0%
L-Aileron 0.0%
Rudder 0.0%
Motor
0.0%
Flap 0.0%
AUX2 0.0%
AUX3 0.0%
DEVO F 1 2 E — 98