Toyota Camry Manual page 55

SS–6
ENGINE MECHANICAL (5S–FE)
SERVICE DATA
Compression
pressure
Difference of pressure between each cylinder
Valve
clearance
Adjusting shim (for repair part)
Ignition timing
Idle speed
Idler pulley Free length
tension spring Installed load at 50.5 mm (1.988 in.)
Cylinder head Warpage
Cylinder block side
Manifold side
Valve seat
Refacing angle
Contacting angle
Contacting width
Valve guide Inside diameter
bushing Outside diameter (for repair part)
Valve Valve overall length
Vale face angle
Stem diameter
Stem oil clearance
Margin thickness
Valve spring Deviation
Free length
Installed tension at 34.7 mm (1.366 in.)
SERVICE SPECIFICATIONS
at 250 rpm STD
w/ Terminals TE1 and E1 connected of DLC1 8 – 12° BTDC @ idle
–
Minimum Intake
Maximum Intake
– ENGINE MECHANICAL (5S–FE)
1,226 kPa (12.5 kgf/cm
Minimum 981 kPa (10.0 kgf/cm
98 kPa (1.0 kgf/cm
at cold Intake 0.19 – 0.29 mm (0.007 – 0.011 in.)
Exhaust 0.28 – 0.38 mm (0.011 – 0.015 in.)
Mark 2.500 2.500 mm (0.0984 in.)
Mark 2.550 2.550 mm (0.1004 in.)
Mark 2.600 2.600 mm (0.1024 in.)
Mark 2.650 2.650 mm (0.1043 in.)
Mark 2.700 2.700 mm (0.1063 in.)
Mark 2.750 2.750 mm (0.1083 in.)
Mark 2.800 2.800 mm (0.1102 in.)
Mark 2.850 2.850 mm (0.1122 in.)
Mark 2.900 2.900 mm (0.1142 in.)
Mark 2.950 2.950 mm (0.1161 in.)
Mark 3.000 3.000 mm (0.1181 in.)
Mark 3.050 3.050 mm (0.1201 in.)
Mark 3.100 3.100 mm (0.1220 in.)
Mark 3.150 3.150 mm (0.1240 in.)
Mark 3.200 3.200 mm (0.1260 in.)
Mark 3.250 3.250 mm (0.1280 in.)
Mark 3.300 3.300 mm (0.1299 in.)
700 ± 50 rpm
42.0 mm (1.654 in.)
32 – 37 N (3.25 – 3.75 kgf, 7.2 – 8.3 lbf)
Maximum 0.05 mm (0.0020 in.)
Maximum 0.08 mm (0.0031 in.)
30°, 45°, 75°
45°
1.0 – 1.4 mm (0.039 – 0.055 in.)
6.010 – 6.030 mm (0.2366 – 0.2374 in.)
STD 11.048 – 11.059 mm (0.4331 – 0.4342 in.)
O/S 0.05 11.050 – 11.077 mm (0.4350 – 0.4361 in.)
STD Intake 97.40 – 97.80 mm (3.8346 – 3.8504 in.)
Exhaust 98.25 – 98.65 mm (3.8681 – 3.8839 in.)
97.1 mm (3.823 in.)
Exhaust 98.0 mm (3.858 in.)
44.5°
Intake 5.970 – 5.985 mm (0.2350 – 0.2356 in.)
E h Exhaust t 5 965 5.965 – 5.980 mm (0.2348 – 0.2354 in.) 5 980
STD Intake 0.025 – 0.060 mm (0.0010 – 0.0024 in.)
Exhaust 0.030 – 0.065 mm (0.0012 – 0.0026 in.)
0.08 mm (0.0031 in.)
Exhaust 0.10 mm (0.0039 in.)
STD 0.8 – 1.2 mm (0.031 – 0.047 in.)
Minimum 0.5 mm (0.020 in.)
Maximum 2.0 mm (0.079 in.)
40.95 – 42.80 mm (1.6122 – 1.6850 in.)
164 – 189 N (16.7 – 19.3 kgf, 36.8 – 42.5 lbf)
Author :
2
, 178 psi) or more
2
, 142 psi)
2
, 14 psi) or less
(0 2348 0 2354 i )
Date :
SS0AD–03
169