Omron CJ1W-SCU32 Operation Manual page 95

No-protocol Mode
Device variable for CJ-series Unit
Port 1
*_P1_SendDelayCfg
*_P1_SendDelaySetCf
g
There is no specific
device variable for CJ-
series Unit to reference
the send delay setting
range.
When you set this set-
ting, set to bits 00 to 14
of
*_P1_SendDelayCfg.
*_P1_HlkCTSCtlCfg
*_P1_NopCfg
*_P1_NopStartCodeY
NCfg
*_P1_NopCRLFCfg
*_P1_NopEndCodeYN
Cfg
*_P1_NopRcvDatSzCf
g
*_P1_NopStartCodeCfg
*_P1_NopEndCodeCfg
* When CTS control is enabled, the request to send signal (RTS) turns ON and the transmission starts after the clear to send
signal (CTS) turns ON. When CTS control is disabled, the request to send signal (RTS) turns ON and the transmission
starts without checking whether the clear to send signal (CTS) is ON.
CJ-series Serial Communications Units Operation Manual for NJ-series CPU Unit(W494)
2 Initial Settings and Allocations of Device Variable for CJ-series Unit
Port 2
*_P2_SendDelayCfg
*_P2_SendDelaySetCf
g
There is no specific
device variable for CJ-
series Unit to reference
the send delay setting
range.
When you set this set-
ting, set to bits 00 to 14
of
*_P2_SendDelayCfg.
*_P2_HlkCTSCtlCfg
*_P2_NopCfg
*_P2_NopStartCodeY
NCfg
*_P2_NopCRLFCfg
*_P2_NopEndCodeYN
Cfg
*_P2_NopRcvDatSzCf
g
*_P2_NopStartCodeCfg
*_P2_NopEndCodeCfg
Type R/W Name
WORD RW Send Delay
Settings
BOOL RW Send Delay
Time
Bit RW Send Delay
string Time (User-
specified)
BOOL RW CTS Control (*) FALSE: No
WORD RW No-Protocol
Settings
BOOL RW No-Protocol
Start Code
Inclusion Set-
ting
BOOL RW No-Protocol CR
+ LF Specifica-
tion Setting
BOOL RW No-Protocol
End Code
Inclusion Set-
ting
USINT RW Number of
Receive Data
Bytes in No-
protocol Mode
USINT RW No-protocol
Start Code
USINT RW No-protocol
End Code
Function
Bits serve the functions
described below.
Bit 15: Send delay timer
Bits 00 to 14: Send delay
Time (user-specified)
0: Default (0 ms)
1: User settings
0 to 300 s (0 to 300,000
ms)
(0000 to 7530 hex; 0 to
30,000 decimal) [Unit: 10
ms]
TRUE: Yes
Bit 12: No-protocol start
code inclusion setting
Bit 09: No-protocol CR +
LF specification setting
Bit 08: No-protocol end
code inclusion setting
Bits 00 to 07: Number of
receive data bytes in no-
protocol mode
TRUE: Yes
FALSE: No (default)
End code
P@_NopCRLFCfg/
P@_NopEndCodeYNCfg:
00: No (specify number of
receive data bytes)
01: Yes
10: CR + LF specified
11: Prohibited
0 (default): 256 bytes
Range: 1 to 255 bytes
Range: 0 to 255
Range: 0 to 255
2-21
2