Omron CJ1W-SCU32 Operation Manual page 474

Index
Index
Numerics
2-wire or 4-wire Switch [WIRE] ............................. 1-28, 2-6
2-wire/4-wire .................................................................. 3-7
3Z4L .................................................................... 4-2, R-78
5V ...........................................................................2-4, 3-5
A
Abort Switch (Protocol Macros) .......................... 2-23, 4-22
Allocated DM Area ........................................................A-9
Allocation Areas for Coils .............................................. 7-7
Applicable Connector ....................................2-5, 2-6, 3-25
Assumed cause ........................................................... 9-31
AT specification ........................................................... 2-10
AT specification destination ........................................... 2-8
Auxiliary Area .......................................................7-3, 7-13
B
Basic Operating Procedure ......................................... 1-23
Baud rate .............1-15, 1-20, 2-17, 4-14, 5-6, 6-6, 7-6, 8-5
Bits ..............................................................1-29, 2-34, 8-3
C
CIO area ....................................................... 7-3, 7-13, A-3
Clearing/Holding the Contents of the Reception Buffer in
Full-duplex Mode ....................................2-19, 4-14, 4-18
Coils Allocation Area ..................................................... 7-6
Command Error .................................................. 9-31, 9-40
Command Format Error ..................................... 9-34, 9-47
Communications condition ...................................1-25, 3-8
Communications distance .................................. 1-15, 1-20
Communications sequence ..................................4-4, 4-10
Comparison Error ............................................... 9-34, 9-46
CompoWay/F ........................................................5-2, 5-33
CompoWay/F Master .................................................... R-7
CompoWay/F Slave Component ................................. 5-23
Connection .................................................................... 3-9
Connection configuration ............................................. 1-15
Connector Pin Layout ......................................2-4, 2-6, 3-5
Continuous I/O refreshing .........................2-19, 4-11, 4-18
Continuous Trace Switch ............................................. 2-23
Continuous Trace Switch (Protocol Macros) ............... 4-22
Controller error ............................................................ 9-30
Controller reset ..........................................1-14, 2-14, 4-23
Converting to CompoWay/F ........................................ 5-23
Converting to Modbus-ASCII ....................................... 5-28
Converting to Modbus-RTU ......................................... 5-26
CPU Unit service monitoring error .......................9-2, 9-26
CPU Unit watchdog timer error ................................... 9-26
CPU Unit WDT error ...................................................... 9-2
Create Device Variable ....................................... 1-24, 2-12
Index-2
CS ..........................................................................2-4, 3-5
CS signal ..................................................................... 2-26
CTS (CS) signal .......................................................... 4-19
CTS Check Error ................................................9-31, 9-39
CTS Control ................................ 2-18, 2-20, 2-21, 5-6, 6-6
CX-Integrator ............................................................... 9-25
CX-Protocol ............................................................1-6, 4-2
D
Data Exchange Method for Link Words ....................... 4-18
Data exchange with the CPU Unit ................................. 2-8
Data Length .................................. 2-16, 4-13, 5-5, 6-5, 8-4
Device name .......................................................1-24, 2-12
Device variable for CJ-series Unit ...............2-8, 2-10, 2-12
Diagnostic ...........................................................1-21, 7-20
Dimensions .................................................................... 2-7
Direct Designation ....................................................... 1-32
Direct setting ............................................................... 1-15
DM ........................................................................7-3, 7-13
DM area .........................................................................A-3
DR ..........................................................................2-4, 3-5
DR signal ..............................................................2-4, 2-26
DstDat ................................................................1-30, 4-41
DTR Check Error ................................................9-31, 9-38
E
E5@N .............................................................1-30, 4-2, 4-8
Edit Special Unit Settings ..........................1-23, 1-24, 2-10
EM ........................................................................7-3, 7-13
End code ..............................................................1-20, 6-2
ER ..........................................................................2-4, 3-5
ER signal ..............................................................1-9, 2-26
ERC ............................................................................... 9-2
ERH ............................................................................... 9-2
Error Log Data Error ...........................................9-31, 9-37
Event ........................................................................... 9-30
Event code .................................................................. 9-31
Event level ................................................................... 9-30
Event Log .................................................................... 9-30
Event name ................................................................. 9-31
ExecPMCR instruction ........................ 1-6, 1-15, 4-2, 4-40
Executing Loopback Test ............................................... 8-2
F
FCS Check Error ................................................9-33, 9-43
FG ..........................................................................2-4, 3-5
Framing Error .....................................................9-34, 9-49
H
Half-duplex/Full-duplex ................................................ 1-23
CJ-series Serial Communications Units Operation Manual for NJ-series CPU Unit(W494)