Omron CJ1W-SCU32 Operation Manual page 476

Index
Send delay ...........................................................1-19, 5-4
Send delay function ..................................................... 5-32
Send Delay Settings ................... 2-18, 2-20, 2-21, 5-6, 6-6
Send Delay Time ........................ 2-18, 2-20, 2-21, 5-6, 6-6
Send Start Timeout Monitoring ...................1-19, 5-4, 5-31
SendCmd instruction ................................................... 5-14
SeqNo ......................................................................... 4-40
Sequence Abort Completed ............................... 9-31, 9-40
Sequence number ................................................. 4-2, R-3
Serial Communications instruction ................................ 2-8
Serial communications port ......................................... 1-14
Serial Communications Unit ...................................1-3, 1-4
Serial Communications Unit Port Settings
Changing Flag .......................................................... 2-34
Serial Gateway .......................................................1-6, 5-2
Serial Gateway Prohibit Switch
(Protocol Macros) ........................... 2-23, 4-22, 5-9, 5-14
Serial Gateway Response Timeout Monitoring
Time ................................................ 2-18, 2-20, 4-14, 5-6
Serial Gateway Send Start Timeout Monitoring
Time ................................................ 2-18, 2-20, 4-14, 5-6
Serial Gateway Timeout Monitoring
Time Settings .................................. 2-18, 2-20, 4-14, 5-6
Serial Port I/O instruction .............................................. 6-2
SerialRcv or SerialRcvNoClear instruction ...........1-34, 6-2
SerialSend ............................................................ 1-34, 6-2
SG ..........................................................................2-4, 3-5
Soft Switches ...................................................... 2-23, 4-22
Software switch ....................................................2-8, 2-14
Specifying Link Word ................................................... 1-32
Specifying Operand ..................................................... 1-32
SrcDat ................................................................ 1-30, 4-41
Standard system protocol ...................................... 4-2, R-3
Start Bits ....................................... 2-16, 4-13, 5-5, 6-5, 8-4
Start code .............................................................1-20, 6-2
Status ..........................................................1-14, 2-8, 2-12
Stop Bits ....................................... 2-16, 4-13, 5-5, 6-5, 8-4
Sysmac Studio ................................................... 1-23, 6-12
System Settings data .................................................. 2-10
System Setup Error ............................................ 9-31, 9-38
System-defined variable ..............................2-8, 2-11, 2-34
T
TER1/2 .......................................................................... 2-3
TERM:Terminating resistance ON/OFF switch ............ 1-28
Terminating resistance ................................................ 1-28
Terminating Resistance Switch [TERM] ........................ 2-6
Tfr (Receive Finished Monitoring Time)
Exceeded ......................................................... 9-32, 9-42
Tfs (Send Finished Monitoring Time)
Exceeded ......................................................... 9-32, 9-42
Time reception buffer cleared ...................................... 4-17
Timeout Error ............................................5-31, 9-33, 9-44
Tr (Receive Wait Monitoring Time) Exceeded .... 9-32, 9-43
Transmission control parameter ...........................1-15, 4-5
Transmission Error ............................................. 9-34, 9-47
Transmission Error (CRC Error) ......................... 9-35, 9-52
Transmission Error Status .................................. 4-29, 7-12
Index-4
U
Unit address .......................................................5-24, 5-28
Unit Configuration ...............................................1-24, 2-12
Unit No. Switch .............................................................. 2-3
Unit number ......................................... 1-14, 1-26, 2-3, 3-2
Unit number setting switch .................................1-26, 9-56
Unit with the same unit number ..................................... 9-2
Use No-protocol Mode .................................................. 6-2
User program .....................................................2-11, 4-42
User-defined variable ..................................2-8, 2-11, 2-13
User-specified Setting
Inclusion ............................. 2-16, 4-13, 5-5, 6-5, 7-5, 8-4
V
V500/V520 ........................................................... 4-2, R-65
W
Wait Release Switch (Protocol Macros) .............2-23, 4-22
WIRE: 2-wire or 4-wire selector switch ........................ 1-28
Work .....................................................................7-3, 7-13
Write Multiple Coils ......................................1-21, 7-3, 7-20
Write Multiple Registers ..............................1-21, 7-3, 7-21
Write Single Coil ..........................................1-21, 7-3, 7-18
Write Single Register ...................................1-21, 7-3, 7-19
CJ-series Serial Communications Units Operation Manual for NJ-series CPU Unit(W494)