Omron CJ1W-SCU32 Operation Manual page 475

Hayes Modem AT Command ....................................R-117
Holding ................................................................. 7-3, 7-13
Holding Registers Allocation Area ................................ 7-6
I
I/O Map .............................................................. 2-12, 2-14
I/O port ............................................................... 2-10, 2-14
Indicator ........................................................................ 2-3
Input Registers Allocation Area ..................................... 7-6
L
Link word setting ......................................................... 1-15
Link Word Specification Data Exchange
Method ............................................................ 2-19, 4-14
Loopback Test ............................................................... 1-6
Loopback Test Switch .......................................... 2-23, 8-2
M
Maximum Number of Bytes in
Protocol Macro Send/Receive Data ................ 4-15, 4-18
Maximum number of data exchange words ................ 1-15
Memory used for CJ-series Unit ................... 1-8, 1-21, 2-8
Messages (communications frame structure) ............. 1-20
Mitsubishi Computer Link Master ................................ R-41
Modbus data model ............................................... 7-3, 7-7
Modbus- RTU Slave Address ........................................ 7-6
Modbus-ASCII ...................................................... 5-2, 5-36
Modbus-RTU ........................................................ 5-2, 5-34
MODBUS-RTU Settings ................................................ 7-6
Modbus-RTU Slave ....................................................... 7-2
Modbus-RTU Slave Address ................................ 7-7, 9-22
Modbus-RTU Slave Mode ............................................. 1-7
Modbus-RTU Slave OMRON Device .......................... 5-26
N
Network address ................................................ 5-24, 5-28
Network Communications Instruction
Enabled Flag .......................................... 1-30, 1-33, 1-34
Node address ..................................................... 5-24, 5-28
No-Protocol CR + LF Specification ...................... 2-21, 6-7
No-protocol End Code ......................................... 2-21, 6-6
No-Protocol End Code Inclusion .......................... 2-21, 6-7
No-protocol Mode ......................................................... 1-7
No-Protocol Settings ............................................ 2-21, 6-6
No-protocol Start Code ........................................ 2-21, 6-6
No-Protocol Start Code Inclusion ........................ 2-21, 6-6
NT-AL001 ............................................................. 1-10, 3-8
Number of Command Format Errors .......................... 7-12
Number of CRC Errors ................................................ 7-12
Number of mountable Units ........................................ 1-14
Number of Normally Received Commands ................. 7-12
Number of Normally Sent Responses ........................ 7-12
Number of receive data bytes during reception ... 1-20, 6-3
Number of Receive Data Bytes in
No-protocol Mode .............................................. 2-21, 6-7
CJ-series Serial Communications Units Operation Manual for NJ-series CPU Unit(W494)
O
One-shot Trace Switch ....................................... 2-23, 4-22
On-request I/O Refreshing ........................ 2-19, 4-10, 4-18
Operand setting .......................................................... 1-15
Operation Data ................................................... 2-10, 2-14
Overrun Error ..................................................... 9-34, 9-48
Overrun Error, Framing Error, or Parity Error
(Transmission Error) ........................................ 9-35, 9-51
P
Parity ..................................... 2-17, 4-14, 5-6, 6-6, 7-5, 8-4
Parity (Even/Odd) .................. 2-17, 4-14, 5-6, 6-6, 7-5, 8-4
Parity Error ......................................................... 9-35, 9-50
PMCR(260) ...................................................................R-3
Port Settings ......................... 2-16, 4-13, 5-5, 6-5, 7-5, 8-4
Port Settings Changing Flag .........1-29, 4-21, 5-8, 6-8, 7-8
Port1/Port2 ........................................................... 1-14, 2-2
Power OFF retention ................................................... 2-10
Processing When a Sequence Ends Abnormally ....... 4-53
Protocol Data Error ................................... 4-24, 9-31, 9-37
Protocol Macro ....................................................... 1-6, 4-2
Protocol Macro Error .......................................... 9-32, 9-41
Protocol Macro Transmission Method ....... 2-18, 4-14, 4-16
Protocol macro Transmission Settings ............... 2-18, 4-14
R
RD .......................................................................... 2-4, 3-5
RD1/2 ..................................................................... 2-3, 8-3
RDA/B .................................................................... 2-6, 3-5
RDY ............................................................................... 9-2
Read Coils .................................................. 1-21, 7-3, 7-14
Read Discrete Inputs .................................. 1-21, 7-3, 7-15
Read Holding Registers .............................. 1-21, 7-3, 7-16
Read Input Registers .................................. 1-21, 7-3, 7-17
Receive counter ................................................... 1-20, 6-3
Receive Data Area .................................... 1-32, 4-42, 4-52
Reception buffer clear timing ............................... 1-20, 6-3
Reception Overflow ............................................ 9-34, 9-46
Recommended cable ...........................2-5, 2-6, 3-19, 3-20
Recommended RS-232C Wiring Example .................. 3-19
Recommended RS-422A/485 Wiring Example ........... 3-20
Response timeout monitoring ..................... 1-19, 5-4, 5-31
RS .......................................................................... 2-4, 3-5
RS signal ..................................................................... 2-26
RS/CS Flow Control .................................................... 4-19
RS-232C ................................................................ 2-4, 3-4
RS-422A/485 ......................................................... 2-5, 3-4
RTS (RS) signal .......................................................... 4-19
RUN .............................................................................. 9-2
S
SD1 ............................................................................... 8-3
SD1/2 ..................................................................... 2-3, 8-3
SDA/B .................................................................... 2-6, 3-5
Send Data Area ................................................. 1-32, 4-42
Index
I
Index-3