Teledyne T300 Operation Manual page 14

Carbon monoxide analyzer

Table of Contents

PART II OPERATING INSTRUCTIONS .................................................................................. 87

4. OVERVIEW OF OPERATING MODES ............................................................................... 89

4.1. Sample Mode ...............................................................................................................................................90

4.1.1. Test Functions .......................................................................................................................................90

4.1.2. Warning Messages ................................................................................................................................93

4.2. Calibration Mode ..........................................................................................................................................94

4.3. Setup MODE ................................................................................................................................................95

4.3.1. Password Security .................................................................................................................................95

4.3.2. Primary Setup Menu ..............................................................................................................................95

4.3.3. The areas accessible under the Setup mode are shown in Table 4-4 and Secondary Setup Menu

(SETUP>MORE) ..............................................................................................................................................95

4.3.4. Secondary Setup Menu (SETUP>MORE) .............................................................................................96

5. SETUP MENU 97

5.1. SETUP à CFG: Configuration Information .................................................................................................97

5.2. SETUP à ACAL: Automatic Calibration ......................................................................................................98

5.3. SETUP àDAS: Internal Data Acquisition System .......................................................................................98

5.4. SETUP à RNGE: Analog Output Reporting Range Configuration .............................................................98

5.4.1. Analog Output Ranges for CO Concentration .......................................................................................98

5.4.2. Physical Range vs Analog Output Reporting Ranges .........................................................................100

5.4.3. Reporting Range Modes: Single, Dual, Auto Ranges .........................................................................100

5.4.3.1. SINGLE Range Mode (SNGL) .....................................................................................................102

5.4.3.2. DUAL Range Mode (DUAL) .........................................................................................................103

5.4.3.3. AUTO Range Mode (AUTO) ........................................................................................................105

5.4.4. Range Units .........................................................................................................................................107

5.4.5. Dilution Ratio (Option) ..........................................................................................................................108

5.5. SETUP à PASS: Password Protection .....................................................................................................109

5.6. SETUP à CLK: Setting the Internal Time-of-Day Clock and Adjusting Speed .........................................111

5.6.1.1. Setting the Internal Clock's Time and Day ...................................................................................111

5.6.1.2. Adjusting the Internal Clock's Speed ............................................................................................111

5.7. SETUP àComm: Communications Ports .................................................................................................113

5.7.1. ID (Machine Identification) ...................................................................................................................113

5.7.2. INET (Ethernet) ....................................................................................................................................113

5.7.3. COM1 and COM2 (Mode, Baud Rate and Test Port) ..........................................................................113

5.8. SETUP àVARS: Variables Setup and Definition ......................................................................................114

5.9. SETUP àDiag: Diagnostics Functions ......................................................................................................116

5.9.1. Signal I/O .............................................................................................................................................118

5.9.2. Analog Output ......................................................................................................................................119

5.9.3. Analog I/O Configuration ......................................................................................................................120

5.9.3.1. Analog Output Voltage / Current Range Selection .......................................................................122

5.9.3.2. Analog Output Calibration ............................................................................................................124

5.9.3.3. Enabling or Disabling the AutoCal for an Individual Analog Output .............................................124

5.9.3.4. Automatic Calibration of the Analog Outputs ...............................................................................126

5.9.3.5. Individual Calibration of the Analog Outputs ................................................................................127

5.9.3.6. Manual Calibration of the Analog Outputs Configured for Voltage Ranges .................................128

5.9.3.7. Manual Adjustment of Current Loop Output Span and Offset .....................................................130

5.9.3.8. Turning an Analog Output Over-Range Feature ON/OFF ...........................................................133

5.9.3.9. Adding a Recorder Offset to an Analog Output ............................................................................134

5.9.3.10. AIN Calibration ...........................................................................................................................135

5.9.3.11. Analog Inputs (XIN1...XIN8) Option Configuration ....................................................................136

5.9.4. Electrical Test ......................................................................................................................................137

5.9.5. Dark Calibration ...................................................................................................................................137

5.9.6. Pressure Calibration ............................................................................................................................137

5.9.7. Flow Calibration ...................................................................................................................................138

5.9.8. Test Chan Output .................................................................................................................................138

5.9.8.1. Selecting a Test Channel Function for Output A4 ........................................................................138

xii

Teledyne API - Model T300/T300M CO Analyzer

06864B DCN6314

Table of Contents