Connector Output Parameters - Siemens CU230P-2 HVAC Parameter Manual

Parameters
Connector/Binector (BICO)-Parameters
1.4.4

Connector Output Parameters

Product: SINAMICS G120, Version: 4301300, Language: eng, Type: CO
r0021
r0025
r0026
r0027
r0032
r0035
r0036
r0037[0...19]
r0060
r0062
r0063[0...2]
r0064
r0066
r0067
r0068[0...1]
r0069[0...6]
r0070
r0072
r0074
r0075
r0076
r0077
r0078
r0079
r0080[0...1]
r0081
r0082[0...2]
r0083
r0084[0...1]
r0087
r0094
r0289
r0752[0...3]
r0755[0...3]
r0944
p1001[0...n]
p1002[0...n]
p1003[0...n]
p1004[0...n]
p1005[0...n]
p1006[0...n]
p1007[0...n]
p1008[0...n]
p1009[0...n]
p1010[0...n]
p1011[0...n]
p1012[0...n]
p1013[0...n]
p1014[0...n]
p1015[0...n]
1-426
CO: Actual speed smoothed / n_act smooth
CO: Output voltage smoothed / V_outp smooth
CO: DC link voltage smoothed / Vdc smooth
CO: Absolute actual current smoothed / I_act abs val smth
CO: Active power actual value smoothed / P_actv_act smth
CO: Motor temperature / Mot_temp
CO: Power unit overload I2t / PU overload I2t
CO: Power unit temperatures / PU temperatures
CO: Speed setpoint before the setpoint filter / n_set before filt.
CO: Speed setpoint after the filter / n_set after filter
CO: Actual speed value / n_act
CO: Speed controller system deviation / n_ctrl system dev
CO: Output frequency / f_outp
CO: Output current, maximum / I_outp max
CO: Absolute current actual value / I_act abs val
CO: Phase current actual value / I_phase act value
CO: Actual DC link voltage / Vdc act val
CO: Output voltage / V_output
CO: Modulat_depth / Modulat_depth
CO: Current setpoint field-generating / Id_set
CO: Current actual value field-generating / Id_act
CO: Current setpoint torque-generating / Iq_set
CO: Current actual value torque-generating / Iq_act
CO: Torque setpoint total / M_set total
CO: Torque actual value / M_act
CO: Torque utilization / M_Utilization
CO: Active power actual value / P_act
CO: Flux setpoint / Flux setpoint
CO: Flux actual value / Flux act val
CO: Actual power factor / Cos phi act
CO: Transformation angle / Transformat_angle
CO: Maximum power unit output current / PU I_outp max
CO: CU analog inputs input voltage/current actual / CU AI inp_V/I
CO: CU analog inputs actual value in percent / CU AI value in %
CO: Counter for fault buffer changes / Fault buff change
CO: Fixed speed setpoint 1 / n_set_fixed 1
CO: Fixed speed setpoint 2 / n_set_fixed 2
CO: Fixed speed setpoint 3 / n_set_fixed 3
CO: Fixed speed setpoint 4 / n_set_fixed 4
CO: Fixed speed setpoint 5 / n_set_fixed 5
CO: Fixed speed setpoint 6 / n_set_fixed 6
CO: Fixed speed setpoint 7 / n_set_fixed 7
CO: Fixed speed setpoint 8 / n_set_fixed 8
CO: Fixed speed setpoint 9 / n_set_fixed 9
CO: Fixed speed setpoint 10 / n_set_fixed 10
CO: Fixed speed setpoint 11 / n_set_fixed 11
CO: Fixed speed setpoint 12 / n_set_fixed 12
CO: Fixed speed setpoint 13 / n_set_fixed 13
CO: Fixed speed setpoint 14 / n_set_fixed 14
CO: Fixed speed setpoint 15 / n_set_fixed 15
SINAMICS G120 Control Units CU230P-2 Parameter Manual (LH9), 11/2009
© Siemens AG 2009 All Rights Reserved