Command And Drive Data Sets - Overview; Command Data Sets (Cds) - Siemens CU230P-2 HVAC Parameter Manual

1.3 Command and Drive Data Sets – Overview
1.3.1

Command Data Sets (CDS)

Product: SINAMICS G120, Version: 4301300, Language: eng, Type: CDS
p0641[0...n]
p0700[0...n]
p0701[0...n]
p0702[0...n]
p0703[0...n]
p0704[0...n]
p0705[0...n]
p0706[0...n]
p0712[0...n]
p0713[0...n]
p0820[0...n]
p0821[0...n]
p0840[0...n]
p0844[0...n]
p0845[0...n]
p0848[0...n]
p0849[0...n]
p0852[0...n]
p0854[0...n]
p1000[0...n]
p1020[0...n]
p1021[0...n]
p1022[0...n]
p1023[0...n]
p1035[0...n]
p1036[0...n]
p1039[0...n]
p1041[0...n]
p1042[0...n]
p1043[0...n]
p1044[0...n]
p1051[0...n]
p1052[0...n]
p1055[0...n]
p1056[0...n]
p1070[0...n]
p1071[0...n]
p1075[0...n]
p1076[0...n]
p1085[0...n]
p1088[0...n]
p1108[0...n]
p1109[0...n]
p1110[0...n]
p1111[0...n]
p1113[0...n]
p1122[0...n]
© Siemens AG 2009 All Rights Reserved
SINAMICS G120 Control Units CU230P-2 Parameter Manual (LH9), 11/2009
CI: Current limit, variable / Curr lim var
Command source selection / Cmd src sel
Pre-assignment digital input 0 / Pre-assignment DI0
Pre-assignment digital input 1 / Pre-assignment DI1
Pre-assignment digital input 2 / Pre-assignment DI2
Pre-assignment digital input 3 / Pre-assignment DI3
Pre-assignment digital input 4 / Pre-assignment DI4
Pre-assignment digital input 5 / Pre-assignment DI5
Pre-assignment digital input 11 / Pre-assign. DI11
Pre-assignment digital input 12 / Pre-assign. DI12
BI: Drive Data Set selection DDS bit 0 / DDS select., bit 0
BI: Drive Data Set selection DDS bit 1 / DDS select., bit 1
BI: ON/OFF1 / ON/OFF1
BI: 1. OFF2 / 1. OFF2
BI: 2. OFF2 / 2. OFF2
BI: 1. OFF3 / 1. OFF3
BI: 2. OFF3 / 2. OFF3
BI: Operation enable / Operation enable
BI: Master ctrl by PLC / Master ctrl by PLC
Speed setpoint selection / n_set sel
BI: Fixed speed setpoint selection Bit 0 / n_set_fixed Bit 0
BI: Fixed speed setpoint selection Bit 1 / n_set_fixed Bit 1
BI: Fixed speed setpoint selection Bit 2 / n_set_fixed Bit 2
BI: Fixed speed setpoint selection Bit 3 / n_set_fixed Bit 3
BI: Motorized potentiometer setpoint raise / Mop raise
BI: Motorized potentiometer lower setpoint / Mop lower
BI: Motorized potentiometer inversion / Mop inversion
BI: Motorized potentiometer manual/automatic / Mop manual/auto
CI: Motorized potentiometer automatic setpoint / Mop auto setpoint
BI: Motorized potentiometer accept setpoint / Mop accept set val
CI: Motorized potentiometer setting value / Mop set val
CI: Speed limit RFG positive direction of rotation / n_limit RFG pos
CI: Speed limit RFG negative direction of rotation / n_limit RFG neg
BI: Jog bit 0 / Jog bit 0
BI: Jog bit 1 / Jog bit 1
CI: Main setpoint / Main setpoint
CI: Main setpoint scaling / Main setp scal
CI: Supplementary setpoint / Suppl setpoint
CI: Supplementary setpoint scaling / Suppl setp scal
CI: Speed limit in positive direction of rotation / n_limit pos
CI: Speed limit in negative direction of rotation / n_limit neg
BI: Total setpoint selection / Total setp sel
CI: Total setpoint / Total setp
BI: Inhibit negative direction / Inhib neg dir
BI: Inhibit positive direction / Inhib pos dir
BI: Setpoint inversion / Setp inv
BI: Bypass ramp-function generator / Bypass RFG
Command and Drive Data Sets – Overview
Parameters
1-409