Glove Box; Instrument Panel Assembly - Dodge Intrepid Service Manual

23 - 46 INSTRUMENT PANEL

GLOVE BOX

REMOVAL
(1) Remove the four screws at bottom of glove box
door.
(2) Open the glove box door and slide sidewalls
inboard to remove the door/box assembly from instru-
ment panel.
(3) Place the glove box on a cloth to protect the
door surface.
(4) Remove the nine screws from backside of the
door.
(5) Separate the inner and outer door.
(6) Remove one screw to the latch.
(7) Remove latch from outer door.
NOTE: If the glove box door is going to be left off
for an extended period of time, the Ignition Off
Draw (IOD) fuse should be pulled to maintain bat-
tery condition.
INSTALLATION
(1) Install latch from outer door.
(2) Install one screw to the latch.
(3) Place teh the inner and outer door together.
(4) Install the nine screws to the backside of the
door.
(5) Slide sidewalls inboard to install the door/box
assembly into instrument panel.
(6) Install the four screws at bottom of glove box
door to instrument panel.
GLOVE BOX LATCH
REMOVAL
(1) Remove the four screws at bottom of glove box
door.
(2) Open the glove box door and slide sidewalls
inboard to remove the door/box assembly from instru-
ment panel.
(3) Place the glove box on a cloth to protect the
door surface.
(4) Remove the nine screws from backside of the
door.
(5) Separate the inner and outer door.
(6) Remove one screw to the latch.
(7) Remove latch from outer door.
NOTE: If the glove box door is going to be left off
for an extended period of time, the Ignition Off
Draw (IOD) fuse should be pulled to maintain bat-
tery condition.
INSTALLATION
(1) Install latch from outer door.
(2) Install one screw to the latch.
(3) Place teh the inner and outer door together.
(4) Install the nine screws to the backside of the
door.
(5) Slide sidewalls inboard to install the door/box
assembly into instrument panel.
(6) Install the four screws at bottom of glove box
door to instrument panel.
INSTRUMENT PANEL
ASSEMBLY
REMOVAL
WARNING: DISCONNECT AND ISOLATE THE NEGA-
TIVE BATTERY CABLE
BEFORE BEGINNING ANY INSTRUMENT PANEL OR
COMPONENT REMOVAL OR INSTALLATION PRO-
CEDURE. THIS WILL DISABLE THE AIRBAG SYS-
TEM. FAILURE TO DISCONNECT BATTERY COULD
RESULT IN ACCIDENTAL AIRBAG DEPLOYMENT
AND POSSIBLE PERSONAL INJURY. ALLOW SYS-
TEM CAPACITOR TO DISCHARGE FOR 2 MINUTES.
(1) Open hood and disconnect the negative battery
cable remote terminal from the remote battery post
(Fig. 1).
(2) Remove one Allen screw to shifter knob.
(3) Remove left and right instrument panel end
covers.
NOTE: On 300M vehicles, the center bezel must be
removed prior to the shifter bezel.
(4) 300M, remove center bezel (Refer to 23 -
BODY/INSTRUMENT
PANEL CENTER BEZEL - REMOVAL).
(5) Using a trim stick (special tool #C-4755) or
equivalent, gently pry up on shifter bezel.
(6) Disconnect two wire connectors, one illumina-
tion bulb socket, and remove.
(7) Remove two screws from lower instrument
panel cover (outside end) and disconnect deck lid
release switch wiring connector. Pull rearward on
lower instrument panel cover releasing clips. Remove
cable to brake release handle. Pull rearward and
remove cover from vehicle.
(8) On six passenger vehicles, remove the lower
floor bin and proceed with Step 14 (Refer to 23 -
BODY/INSTRUMENT
REMOVAL).
(9) On five passenger vehicles, use trim stick or
equivalent to gently remove center bezel (Refer to 23
REMOTE TERMINAL
PANEL/INSTRUMENT
PANEL/STORAGE BIN
LH
-