160: St. Mic + Preamp; 161: Multitap Cho/Delay - Korg M3 Parameter Manual

Effect Guide

160: St. Mic + PreAmp

(Stereo Mic Modeling + PreAmp)
This is a stereo mic and preamp simulator (see p.457, 025:
Mic Model+PreAmp (Mic Modeling + PreAmp)). For
example you might use this to simulate micing of a stereo
source such as a rotary speaker.
Stereo In - Stereo Out
Left
Mic Simulation
Mic Simulation
Right

161: Multitap Cho/Delay

(Multitap Chorus/Delay)
This effect has six chorus blocks with different LFO phases.
You can produce a complex stereo image by setting a
different delay time and depth for each block. You can
control the delay output level via a modulation source.
Wet: Mono In - Stereo Out / Dry: Stereo In - Stereo Out
Left
Feedback
+
Right
0 [degree]
180 [degree]
60 [degree]
240 [degree]
120 [degree]
300 [degree]
LFO: Triangle
D -mod
On/Off Control
LFO
a Frequency 0.02...13.00
[Hz]
Tap1 (000)
0...2000
[msec]
Depth 0...30
Always On,
b
Always Off,
On➝Off
Status
(Dm),
Off➝On
(Dm)
Tap2 (180)
0...2000
[msec]
Depth 0...30
c
Always On,
Always Off,
Status
On➝Off (Dm),
Off➝On (Dm)
Tap3 (060)
0...2000
[msec]
Depth 0...30
Always On,
d
Always Off,
On➝Off
Status
(Dm),
Off➝On
(Dm)
518
Tube Pre Amp
Output Level
Tube Pre Amp
Tap1 Delay
Tap2 Delay
Tap3 Delay
Tap4 Delay
Tap5 Delay
Tap6 Delay
Panning Preset
Sets the speed of the LFO
Sets the Tap1 (LFO phase=0
degrees) delay time
Sets the Tap1 chorus depth
Selects on, off, or modulation
source for the control of Tap1
output
p.518
Sets the Tap2 (LFO phase=180
degrees) delay time
Sets the Tap2 chorus depth
Selects on, off, or modulation
source for the control of Tap2
output
p.518
Sets the Tap3 (LFO phase=60
degrees) delay time
Sets the Tap3 chorus depth
Selects on, off, or modulation
source for the control of Tap3
output
p.518
Tap4 (240)
[msec]
Depth
e
Status
Tap5 (120)
[msec]
Depth
f
Wet / Dry
Status
Tap6 (300)
[msec]
Depth
Wet / Dry
g
Status
h Panning
Preset
Tap1
Feedback
i Src
Amt
Wet/Dry
Wet / Dry
j Src
Amt
b, c, d, e, f, g: Status
Wet / Dry
These parameters set the output status of each Tap.
Always On: Output is always on. (No modulation)
Always Off: Output is always off. (No modulation)
On→Off (dm): Output level is switched from on to off
depending on the modulation source.
Off→On (dm): Output level is switched from off to on
depending on the modulation source.
Combining these parameters, you can change from 4-phase
chorus to two-tap delay by crossfading them gradually via
the modulation source during a performance.
h: Panning Preset
This parameter selects combinations of stereo images of the
tap outputs.
Sets the Tap4 (LFO phase=240
0...2000
degrees) delay time
0...30 Sets the Tap4 chorus depth
Always On,
Always Off, Selects on, off, or modulation
On➝Off source for the control of Tap4
(Dm), output
Off➝On
(Dm)
Sets the Tap5 (LFO phase=120
0...2000
degrees) delay time
0...30 Sets the Tap5 chorus depth
Always On,
Always Off, Selects on, off, or modulation
On➝Off source for the control of Tap5
(Dm), output
Off➝On
(Dm)
Sets the Tap1 (LFO phase=300
0...2000
degrees) delay time
0...30 Sets the Tap6 chorus depth
Always On,
Always Off, Selects on, off, or modulation
On➝Off source for the control of Tap6
(Dm), output
Off➝On
(Dm)
1 : L 1 2 3 4 5 6 R,
Selects the stereo panning
2 : L 135 246 R,
pattern for each tap
3 : L 1 3 5 2 4 6 R,
4 : L 1 4 5 6 3 2 R
–100...+100 Sets the Tap1 feedback amount
Selects the modulation source
for the Tap output level,
Off...Tempo
feedback amount, and effect
balance
Sets the modulation amount of
–100...+100
Tap1 feedback amount
Dry, 1 : 99... Sets the balance between the
99 : 1, Wet effect and the dry input
Selects a modulation source for
Off...Tempo
Wet/Dry
Sets the modulation amount
–100...+100
for Wet/Dry
p.518
p.518
p.518
p.518