Media: Menu Command - Korg M3 Parameter Manual

Media mode

Media: Menu Command

Tip: In each page, you can access (or switch on/off) up to the
first ten menu commands by holding down the ENTER
switch and pressing the corresponding numeric key 0–9.
Tip: While this command is open, the ENTER switch will
operate as the OK button and the EXIT switch will operate
as the Cancel button.
0–1: Load Menu Command
Hide unknown files
If you select Hide unknown files, a check mark will appear
at the left of "Hide unknown files." In this state, undefined
files will not be shown in the directory window. However,
this is valid only if there are DOS files in the current
directory.
Translation
When Translation is on (checked), you'll see the full names
of the Multisamples and Samples on the media, instead of
the abbreviated DOS names.
Note that on media, Multisamples are stored as .KMP (Korg
Multisample Parameter) files, and Samples are stored as
.KSF (Korg Sample Format) files.
Lock/Unlock selected
This locks/unlocks the file or directory that's selected in the
directory window (Media 0–1c). If you lock the file or
directory, the lock icon ("Lock") will appear, and
overwriting, copying, or deleting will not be possible.
1. In the directory window (Media 0–1c), select the file or
directory that you want to lock or unlock.
2. Select Lock/Unlock selected; the selected file or direc-
tory will alternately be locked or unlocked.
Sort
This function sorts the files in the current directory.
1. Use Type to select how the files will be sorted, and use
Order to specify the direction.
Type Order
No order ---
Ascent
Name
(Directory
First)
Descent
Ascent
Name
Descent
Ascent
Size
Descent
Ascent
Date
Descent
398
Unsorted
Sort in alphabetical order, first directories
and then files
Sort in reverse alphabetical order, first
directories and then files
Sort alphabetically
Sort in reverse alphabetical
Sort in ascending order of size
Sort in descending order of size
Sort in ascending order of date
Sort in descending order of date
Load selected
This loads the file or directory selected in the directory
window (Media 0–1c) into internal memory.
1. In the directory window (Media 0–1c), select the file or
directory that you want to load.
2. Select Load selected.
A dialog box will appear. The dialog box that appears will
depend on the file you are loading. For more information,
please see page 399.
Specify the various items as necessary.
Note: You can also access the same dialog box by pressing
the Load button instead of Load selected.
If a file to be loaded cannot be found, or when
loading a file that was saved across media
If a necessary file cannot be found in the current directory or
in a lower directory when loading multisamples, sample
data, .PCG, or .SNG files, a dialog box like the following
(Where is a ...) will appear.
This dialog box will appear in the following cases.
• If when loading a .KSC file, a .KMP file used by it cannot
be found.
• If when loading a .KMP file, a .KSF file cannot be found.
• If when loading an S1000/S3000 format Program file, a
Sample file cannot be found.
• If loading a .KSF file that was larger than the media
capacity and was therefore saved on multiple media,
when the first media has been loaded and the second
media needs to be specified.
• When loading a .PCG file that was split across two or
more volumes of media, when the first volume has been
loaded and the second media is now required.
• When loading a .PCG file and also simultaneously
loading a .SNG file, if the identically-named .SNG file is
not found in the current directory after loading the .PCG
file.
If this dialog box appears, take the following action.
1. Select the directory that contains the file indicated by
"Where is a..."
If the specified file is located on another media, exchange
media. Then press the directory window in the display to
make the M3 recognize the media, and select the
appropriate directory.
It is not possible to open .PCG, or .SNG files in the
"Where is a ..." dialog box. The Open button cannot be
used for .PCG, or .SNG files.
2. Press the Select button to resume loading.