0-6: Karma Rtc - Korg M3 Parameter Manual

Program mode
Link to Drum Trk
This links KARMA with the pattern playback of the drum
track.
On (checked): The KARMA performance will be linked
with the starting and stopping of the drum track. If this is
On, the front panel LINKED LED (located between the
DRUM TRACK ON/OFF and KARMA ON/OFF switches)
will light.
If you turn on the KARMA ON/OFF switch and play the
keys of the KYBD-61/73/88 (or receive a note-on message),
KARMA will not be triggered. When you turn on the DRUM
TRACK ON/OFF switch, KARMA will start the moment the
drum track starts.
When you turn the DRUM TRACK ON/OFF switch on
(when Trigger Mode is Start Immediately), KARMA will be
triggered and will begin operating. When KARMA
"LATCH" is on, and "Trigger Mode" is Wait KBD Trig, it
will begin operating when you play a key (or receive a note-
on message).
If you turn the DRUM TRACK ON/OFF switch off while
KARMA is operating, KARMA will also stop if KARMA
"LATCH" is Off.
Off (unchecked): KARMA will not synchronize with the
drum track.
▼0–5: Menu Command
• 0: Write Program ☞p.106
• 1: Panel–SW Solo Mode On ☞p.106
• 2: Exclusive Solo ☞p.107
• 3: Copy X–Y Motion ☞p.107
• 4: Copy KARMA Module ☞p.114
• 5: Initialize KARMA Module ☞p.115
• 6: Copy Scene ☞p.115
• 7: Swap Scene ☞p.115
• 8: Capture Random Seed ☞p.116
For more information, please see "Program: Menu
Command" on page 106.
6
[Off, On]
0–6: KARMA RTC
0–6a
0–6b
0–6c
Using the control surface for KARMA settings
You can use the control surface to control the KARMA
function's KARMA Switches and KARMA Sliders. You can
make these settings using the front panel mixer section, or in
the P0: Play– Control Surface page display. The following
explanation describes how to make settings from the front
panel.
KARMA Switches
1. Press the CONTROL ASSIGN KARMA switch.
2. Press the MIX PLAY/MUTE 1–8 switches to turn the
KARMA Switches On/Off.
KARMA Sliders
1. Press the CONTROL ASSIGN KARMA switch.
2. Move the MIX VOLUMES 1–8 sliders.
MODULE CONTROL and scene switching
In Program mode, only KARMA Module A can be used.
In Combination and Sequencer modes, the four modules A,
B, C, and D can be used. Use the MODULE CONTROL
switch to switch between them.
There are eight KARMA scenes, and you can use the
SCENES 1/5–4/8 switches to switch between them. Each
scene memorizes the settings of the KARMA Switches 1–8
and KARMA Sliders 1–8. By switching scenes, you can
instantly switch between these settings to add even more
variety to the sound generated by KARMA.
When you press the CONTROL ASSIGN KARMA switch,
the 1–4 or 5–8 LED will blink as the next choice. When you
press one of the 1/5–4/8 switches, the corresponding
KARMA scene will be selected.
0–6a: Program Select, Tempo
Bank (Bank Select)
[INT–A...F, GM, g(1)...g(9), g(d), USER–A...G]
Program Select
This shows the bank, number, and name of the currently
selected program. Here you can also select a program. For
more information, please see "0–1a: Program Select" on
page 2.
(Tempo)
For more information, please see " (Tempo)" on page 3.
[0...127 (INT–A...F, USER–A...G),
1...128 (G, g(1)...g(9), g(d))]
[040.00...300.00, EXT]
0–6
Menu