Mixer Input - Korg M3 Parameter Manual

Program mode
Note: Solo applies to oscillators 1 and 2, the drum track, and
the audio inputs.
Note: OSC2 Solo cannot be set for a program whose
Oscillator Mode is Single or Drums.
Note: The Solo On/Off setting is not saved when you write
the program.
Exclusive Solo
The menu's Exclusive Solo parameter also affects the way
that Solo works. If Exclusive Solo is off (unchecked),
Multiple Solo will be active, allowing you to turn Solo on/
off for more than one of the items oscillators 1 and 2, the
drum track, and audio inputs. Each time you press a SOLO
button, the solo setting will alternate between on and of.
If Exclusive Solo is on (checked), only one of the applicable
items can be soloed simultaneously. In this mode, pressing a
SOLO button automatically disables any previous solos.
Tip: You can also toggle Exclusive Solo by holding ENTER
and pressing 2 on the numeric keypad.
OSC Volume:
MIX VOLUMES slider 1, 2, 3
Here you can adjust the output level of oscillators 1 and 2.
This is a volume control that is independent of the Amp
Level parameter. You can also adjust the output level of the
drum track.
OSC 1 Volume
This slider adjusts the volume of Oscillator 1.
OSC 2 Volume
This slider adjusts the volume of Oscillator 2.
Drum Trk Volume
Adjusts the volume of the drum track.
16

Mixer Input

0–8a
0–8b
[Off, On]
0–8d
Mixer Input lets you adjust the volume and switch the Play/
Mute and Solo On/Off status of the four audio inputs
Analog Input 1, 2 and S/P DIF IN L, R
For example on stage, you could use this page screen as a
submixer to control the output of other sound modules for
output together with the M3-M's own sounds.
FireWire L and R can be used if the EXB-FW option is
installed.
Note: If the EXB-FW is installed, the two inputs FireWire L
and R will be added to the Analog Input 1/2 and S/P DIF
L/R listed above.
[000...127]
Other Audio settings
Each audio input can be assigned to up to three busses:
• An Output/IFX Bus
[000...127]
• An FX Control Bus
• An AUX Bus
[000...127]
You can set up these bus assignments on the P0: Play–
Sampling/Audio In page. For more information, please see
"0–7: Sampling/Audio In" on page 8.
0–8d: Mixer Input
Use/Edit Global Setup
Programs can use the single, Global audio input mixer
setup, or can instead have their own custom settings.
On (checked): The Global P0: Basic Setup– Audio page
settings for Analog Input 1, 2, S/P DIF L, R, FireWire L and
R (if the EXB-FW is installed) will be used.
If you switch from a program (or combination or song) for
which Use/Edit Global Setup is on to another program (or
combination or song), the same Audio Input settings will be
used.
Also, any edits made on this page will affect the Global
setting, along with any other Programs, Combinations, or
Songs which use the Global setting.
Off (unchecked): Turn Use/Edit Global Setup Off if you
want to use the Analog Input 1, 2, S/P DIF L, R, FireWire L
and R (if the EXB-FW is installed) settings made
individually for each program (or combination or song).
Use this setting if you want to preserve specific mixer
settings for each program, if you want to use unusual
submixer settings, or if you want to apply effect processing
to specific input signals.
On the other hand, it may sometimes be convenient to save
a particular mixer setup with an individual Program, to set
up special sub-mixer settings or effects processing for
particular inputs.
0–8
Menu
[Off, On]