9-2: Mfx1; 9-3: Mfx2, 9-4: Tfx - Korg M3 Parameter Manual

Combination mode
9–2: MFX1
9–2a
Here you can edit the parameters of the effect you selected
for MFX1 in the P9: MFX/TFX– Routing page.
9–2a: MFX1
MFX1 On/Off
This turns master effect 1 on/off. This is linked with the on/
off setting in the P9: MFX/TFX– Routing page.
Note: If Control Assign is RT Control, MFX 1 On/Off can be
controlled by switch 6. MFX2 and TFX are controlled by
switches 7 and 8, respectively.
Ch (Control Channel)
Specifies the MIDI channel that will control dynamic
modulation (Dmod) for the master effect.
Ch01...Ch16: The specified MIDI channel will be used for
control.
G ch: The global MIDI Channel (Global 1–1a) will be used
for control. Normally you will use the G ch setting.
P (Effect Preset)
[P00, P01...15, U00...15, ---------------]
Effect Presets let you easily store and recall all of the settings
for an individual effect. You can store up to 16 user presets
for each effect type, in addition to 15 re-writable factory
presets.
The same presets appear in all of the modes (Program,
Combination, Sequence, and Sampling).
Note that edits to effects parameters are automatically
stored with the Combination–you don't need to store them
as an Effect Preset. Presets just make it easier to re-use your
favorite settings.
For instance, you can save an Effect Preset while working on
a particular Combination, and then later use the same Effect
Preset in a different Program, Combination, or Song.
P00: Initial Set: These are the default settings that are
recalled when you select an effect type in the P9: MFX/TFX–
Routing page. You can't save your own settings here.
P01...P15: These contain preset data that Korg plans to
provide in the future. We recommend that you store your
settings in U00–U15.
U00...U15: These are areas in which you can store your own
settings.
---------------: This shows that no Effect Preset has been
selected. You'll see this if you've just selected an effect,
written a Combination, or selected a new Combination.
Selecting this setting from the menu will not have any effect.
Note: Combinations save the effects parameter settings, but
they don't save the number of the selected Effect Preset. If
you select an Effect Preset, and then save the Combination,
the Effect Preset setting will revert to "--------------."
184
For more details, please see "Using Effect Presets" on
page 101.
MFX1 Parameters
9–2
Here you can set the effect parameters of the insert effect
Menu
you chose in the P9: MFX/TFX– Routing page.
For details on the master effects, please see the "Effect
Guide" on page 421.
▼9–2: Menu Command
• 0: Write Combination ☞p.185
• 1: Panel–SW Solo Mode On ☞p.106
• 2: Exclusive Solo ☞p.107
• 3: Copy MFX/TFX ☞p.118
• 4: Swap MFX/TFX ☞p.118
• 5: Write FX Preset ☞p.190
For more information, please see "Combination: Menu
Command" on page 185.
[Off, On]
9–3: MFX2,
9–4: TFX
These pages let you edit the parameters of Master Effect 2
and Total Effect. To select different effects types, use the P9:
[Ch01...16, G ch]
MFX/TFX– Routing page.
The parameters for MFX2, TFX is the same as for MFX1. For
more information, please see "9–2: MFX1," above.