7-2-2: Perf Rtp - Korg M3 Parameter Manual

Note: The correspondence between the KARMA Sliders,
Switches and MIDI control change messages can be
specified in Global P2: Controllers– MIDI CC# Assign. For
SW1...8 and Slider (SW) 1...8, a MIDI control change
message value of less than 64 will be "off," and 64 or greater
will be "on."
Dny1...Dny8 (DynaMIDI 1...8): This corresponds to
Dynamic MIDI 1...8.
Select this if you wish to control a GE parameter using the
controller selected for Source in Dynamic MIDI (Prog 7–2–
3). (Set the Dynamic MIDI "Destination" to RT Params
Control.)
POL. (GE Real-Time Parameter Polarity)
This sets the polarity of the selected controller.
+: In the case of SL1–SL8 (Slider 1–8), moving down from
the center will move the value towards the "Minimum"
setting, and moving up from the center will move towards
the "Maximum" setting.
In the case of SL1s–SL8s (Slider SW 1–8), the bottom of the
slider throw will be "Minimum," and the top will be
"Maximum."
In the case of SW1–8, the parameter will be "Maximum"
when the LED is lit.
–: In the case of SL1–SL8 (Slider 1–8), moving down from
the center will move the value towards the "Maximum"
setting, and moving up from the center will move towards
the "Minimum" setting.
In the case of SL1s–SL8s (Slider SW 1–8), the bottom of the
slider throw will be "Maximum," and the top will be
"Minimum." In the case of SW1–8, the parameter will be
"Maximum" when the LED is dark.
▼7–2–1: Menu Command
• 0: Write Program ☞p.106
• 1: Panel–SW Solo Mode On ☞p.106
• 2: Exclusive Solo ☞p.107
• 3: Copy KARMA Module ☞p.114
• 4: Initialize KARMA Module ☞p.115
• 5: Copy Scene ☞p.115
• 6: Swap Scene ☞p.115
• 7: Capture Random Seed ☞p.116
For more information, please see "Program: Menu
Command" on page 106.
PROG P7–2: KARMA 2 7–2–2: Perf RTP (Perf Real-Time Parameters)
7–2–2: Perf RTP
(Perf Real-Time Parameters)
7–2
–2a
7–2
–2b
[+, –]
Here you can assign controllers to KARMA Performance
Real-Time Parameters (Perf. RTP) outside of the GE Real-
Time Parameters that control the internal settings of the GE.
Examples include the KARMA Key Zone parameters (Prog
7–1–1) and KARMA Control and Trigger parameters (Prog
7–1–7, 7–1–8).
By assigning these to KARMA Sliders 1–8 and KARMA
Switches 1–8 etc., you can control them in real-time while
you play.
In Perf Real-Time Parameters 1–8, if you select a
parameter by Group and Parameter and On (checked)
Module A, that parameter can no longer be edited as a
KARMA Key Zone parameter (Prog 7–1–1) or
KARMA Control and Trigger parameter (Prog 7–1–7,
7–1–8).
7–2–2a: Tempo
(Tempo)
For more information, please see " (Tempo)" on page 3.
7–2–2b: Perf RTP 1–2, 3–4, 5–6, 7–8
(Perf Real-Time Parameters)
Select (Perf RTP Select)
This selects the performance realtime parameters you'll edit.
Group [Off, PE, Mix, Control, Trigger, Key Zones,
Selects the group of parameters that you wish to choose a
"Parameter" from.
The KARMA parameters are divided into six groups.
Parameter [Time Signature...Retrigger Each Time]
Indicates the parameter that you wish to assign.
The parameters that can be selected will differ according to
the Group setting, above.
Min (Min Value)
This sets the parameter value when the selected controller is
at its minimum point—for instance, when a slider is at the
bottom of its throw. Note that you can reverse the action of
the controller by setting this to be higher than the MAX
value, below.
The available values will depend on the selected parameter.
When a parameter is selected, the minimum parameter
value will be set as the default.
7–2
–2
Menu
[040.00...300.00, EXT]
[1–2, 3–4, 5–6, 7–8]
Random Seeds]
[–8192...+8191]
91