028: St. Biphase Mod - Korg M3 Parameter Manual

Dry, 1 : 99... Sets the balance between the
Wet/Dry
99 : 1, Wet effect and the dry input
Selects a modulation source for
j Src Off...Tempo
Wet/Dry
Sets the modulation amount
Amt –100...+100
for Wet/Dry
g: High/Low Split Point
This parameter sets the frequency that splits the high and
low range. Only the high range will be sent to the chorus
block.
h: Feedback
Sets the feedback amount of the chorus block. Increasing the
feedback will allow you to use the effect as a flanger.

028: St. Biphase Mod.

(Stereo Biphase Modulation)
This stereo chorus effect adds two different LFOs together.
You can set the Frequency and Depth parameters for each
LFO individually. Depending on the setting of these LFOs,
very complex waveforms will create an analog-type,
unstable modulated sound.
Stereo In - Stereo Out
Left
Chorus/Flanger
Feedback
Chorus/Flanger
Right
180 [degree]
LFO1: Tri / Sine
LFO2: Tri / Sine
LFO1 Triangle,
Selects LFO1 waveform
Waveform Sine
Triangle,
LFO2 Selects LFO2 waveform
a Sine
Switches the LFO phase
0 deg,
Phase Sw difference between left and
180 deg
right
LFO1
Frequency 0.02...30.00 Sets the LFO1 speed
[Hz]
b Selects the modulation source
Src Off...Tempo
of LFO1&2 speed
–30.00... Sets the modulation amount of
LFO1 Amt
+30.00 LFO1 speed
LFO2
Frequency 0.02...30.00 Sets the LFO2 speed
[Hz]
c
–30.00... Sets the modulation amount of
Amt
+30.00 LFO2 speed
Individual, Selects either (individual) LFO,
LFO1 Type Common1, Common FX LFO1, or Common
Common2 LFO2
d
Sets the phase offset when
CmnLFO
–180...+180 LFO1 Type = Common 1 or
Offset [deg]
Common 2
Individual, Selects either (individual) LFO,
LFO2 Type Common1, Common FX LFO1, or Common
Common2 LFO2
e
Sets the phase offset when
CmnLFO
–180...+180 LFO2 Type = Common 1 or
Offset [deg]
Common 2
Sets the depth of LFO1
Depth1 0...100
modulation
Selects the modulation source
f Src Off...Tempo
of LFO1&2 modulation depth
Sets the modulation amount of
Amt –100...+100
LFO1 modulation depth
Sets the depth of LFO2
Depth2 0...100
modulation
g
Sets the modulation amount of
Amt –100...+100
LFO2 modulation depth
Wet / Dry
High Damp
High Damp
Wet / Dry
p.448
p.448
p.448
p.448
Chorus, Flanger, and Phaser (Cho/Fln Phaser)
L Pre Delay Sets the delay time for the left
0.0...50.0
[msec] channel
h
R Pre Delay Sets the delay time for the right
0.0...50.0
[msec] channel
Sets the feedback amount
Feedback –100...+100
i
High Damp Sets the damping amount in
0...100
[%] the high range
–Wet... Sets the balance between the
Wet/Dry –1 : 99, Dry, effect and the dry input
1 : 99...Wet
j Selects a modulation source for
Src Off...Tempo
Wet/Dry
Sets the modulation amount
Amt –100...+100
for Wet/Dry
LFO1
Depth1
LFO2
Depth2
p.458
p.458
p.459
p.450
Bi-Phase Modulation LFO
+
459