Seq P8: Ifx (Insert Effect); Seq P8-1: Ifx; 8-1-1: Routing1 T01-08; 8-1-2: Routing1 T09-16 - Korg M3 Parameter Manual

SEQ P8: IFX (Insert Effect)

You can also specify the bus routing for the program used by
each MIDI track 1–16. For instance, you can:
• Send the output of a track to an insert effect
• Route a sound to an insert effect
SEQ P8–1: IFX
8–1–1: Routing1 T01–08,
8–1–2: Routing1 T09–16
8–1
–1a
8–1
–1b
8–1
–1c
8–1
–1d
Specifies the bus to which the program oscillator(s) used by
MIDI tracks 1–8 and 9–16 will be sent. You can also set the
send levels to the master effects from this page.
8–1–1(2)a: Routing Map
This area shows the insert effect routing (Bus Select), the
name of the assigned effect, the on/off status, chaining, and
the output bus that follows the insert effect. The type of
insert effect, the on/off status, and the chain settings can be
edited in the 8–1–3: Insert FX Setup page.
8–1–1(2)b: Track Select, Tempo, RPPR
8–1–1(2)c: Track Info
For more information, please see "2–1: Trim T01–08, 2–2:
Trim T09–16" on page 224.
8–1–1(2)d: Routing1
Bus Select (IFX/Indiv. Out Assign)
[DKit, L/R, IFX1...5, 1...4, 1/2, 3/4, Off]
This specifies the output bus for the track's program
oscillator. This parameter can also be edited from the P8–2–
1: MIDI Routing 2 page.
L/R: Output to the L/R bus.
IFX1, 2, 3, 4, 5: Output to the IFX1–5 buses.
1, 2, 3, 4: The track will be output in mono from the
corresponding AUDIO OUTPUT (INDIVIDUAL) 1, 2, 3, and
4.
1/2, 3/4: The track will be output in stereo according to its
pan setting from the corresponding AUDIO OUTPUT
(INDIVIDUAL) pairs 1/2, or 3/4.
SEQ P8: IFX (Insert Effect) 8–1–1: Routing1 T01–08, 8–1–2: Routing1 T09–16
• Make detailed settings for insert effects
• Make common LFO settings for effects
For details on Insert Effects, please see "Effect Guide" on
page 421.
Off: The track will not be output from the L/R bus, IFX1–5
buses, or Individual 1–4 buses. Choose the Off setting if you
want the program oscillator output of the track to be
connected in series to a master effect. Use Send1 (to MFX1)
and Send2 (to MFX2) to specify the send levels.
Tip: You can create a wide variety of routings by using each
8–1
–1
track's Bus Select and the Chain to and Chain settings (Seq
Menu
8–1–3b) that follow the insert effect.
DKit: You can select this only if the specified program is a
drum program (Oscillator Mode Drums).
The Bus Select, FX Control Bus, Send1, and Send2 settings
(Global 5–4b) for each key of the selected drum kit will be
used. Check this setting if you want to apply an individual
insert effect to each drum instrument, or to send individual
drum instruments to AUDIO OUTPUT (INDIVIDUAL).
Tip: In most preloaded drumkits, the drum instruments have
the same Bus Select settings according to their type, as
follows.
Snares → IFX1
Kicks → IFX2
Other → IFX3
If you want to edit these routings, use the DrumKit IFX
Patch menu command. For more information, please see
"DrumKit IFX Patch" on page 190.
Send1 (MFX1)
Send2 (MFX2)
For each track, these parameters set the send level to master
effects 1 and 2. These settings are valid when Bus Select is
set to L/R or Off. When IFX 1–5 are selected, the send levels
to master effects 1 and 2 are set by the Send1 and Send2
parameters of the IFX page, after the sound has passed
through IFX1–5.
If Bus Select is set to 1, 2, 3, 4, 1/2, or 3/4, these settings are
ignored.
The Send 1 and 2 setting you specify here are used when
playing-back or recording from the beginning of the song. If
you modify these settings during recording, your changes
will be recorded as performance data; the send amounts will
change accordingly during playback. You can also modify
these settings during playback. However if Send 1 and 2
data has been recorded, the settings will change according to
the recorded data.
If Status (Seq 3–1(2)c) is either INT or BTH, CC#93 and
#91 can be received to control send 1 and 2 respectively
and change their settings. When you switch songs or
return to the beginning of a song, tracks whose Status is
EXT, EX2 or BTH will transmit these settings via MIDI.
This data will be transmitted on the MIDI channel of
each track as set by MIDI Channel (Seq 3–1(2)c). The
actual send level is determined by multiplying the
value of these parameters with the send level settings of
the oscillator(s) of the program used by the track
(Send1 and Send2, Prog 8–1d).
[000...127]
[000...127]
257