1-6: Controllers Setup - Korg M3 Parameter Manual

1–4(5)c: Enable Combi X–Y CC,
Enable Program X–Y CC
Track 01
Enable Seq X–Y CC
This controls whether or not the track will receive the Song's
X–Y CCs.
If this is On, the track will receive the CCs, and the track's
Program will respond to them according to its own AMS
settings.
If this is Off, the track will not receive the CCs. This can be
useful if the Song's X–Y CCs are causing unwanted
modulation, or conflicting with the Program's own X–Y
CCs.
Enable Prog X–Y CC
This controls whether or not the Program's own X–Y CCs
will be active.
If this is On, the Program's X–Y CCs will work as AMS
sources, just as they did in Program mode. The CCs will not
affect any other tracks, even if they are set to the same MIDI
channel.
Note that in some cases, the X–Y CCs may have been used
for modulating the Program's effects via Dmod. This
functionality is not carried into the Song; for modulating the
Song's effects, use the Song's X–Y CCs instead.
If Enable Program X–Y CC is Off, then the Program's X–Y
CCs will have no effect. This can be useful if they are
conflicting with the Song's X–Y CCs.
Tracks 02...08, 09...16
The settings for Tracks 2–8 and 9–16 are identical to those for
Track 01, as described above.
▼1–4(5): Menu Command
• 0: Memory Status ☞p.271
• 1: Exclusive Solo ☞p.107
• 2: Rename Song ☞p.271
• 3: Delete Song ☞p.271
• 4: Copy From Song ☞p.271
• 5: Load Template Song ☞p.271
• 6: Save Template Song (Save as User Template
Song) ☞p.272
• 7: FF/REW Speed ☞p.272
• 8: Set Location (Set Location for Locate Key) ☞p.272
• 9: GM Initialize ☞p.273
• 10: Copy From Combi (Copy from
Combination) ☞p.273
• 11: Copy from Program ☞p.273
For more information, please see "Sequencer: Menu
Command" on page 271.
1–6: Controllers Setup
1–6a
[Off, On]
1–6b
1–6c
Here you can specify the SW1 and SW2 switch and 5–8
[Off, On] slider functions of the song when Control Assign
REALTIME CONTROL is selected.
When you operate these switches and sliders during
recording, the MIDI messages assigned to them will be
recorded.
Note: SW1 and SW2 can be controlled by the KYBD-61/73/
88's SW1 and SW2 switches.
Note: The Panel Switch Assign setting of the program
assigned to each track will have no effect.
1–6a: Track Select, Tempo, RPPR, Track
Info, Selected Track Info
Track Select
(Tempo)
RPPR
Here you can select the track, specify the tempo that will
control KARMA etc., and turn RPPR on/off.
For more information, please see "0–1–1(2)a: Location,
Meter, Tempo, Tempo Mode, Song Select, Track Select, Reso,
RPPR" on page 195.
Selected Track Info
This area shows detailed information about its track
assignments.
For more information, please see "Selected Track Info" on
page 199.
1–6b: Panel Switch Assign
SW (SW1 Assign)
This assigns the function of SW1. For more information,
please see "List of SW 1/2 assignments" on page 597.
Note: If the KYBD-61/73/88 is connected, the on/off status
of the SW1, SW2 switches is memorized when you save it.
If you change the function setting, the status is reset to off.
Mode (SW1 Mode)
This specifies the on/off operation when you press the
KYBD-61/73/88's SW1 switch.
Toggle: The function will alternate between on and off each
time you press the SW1 switch.
Momentary: The function will be on only while you
continue holding down the SW1 switch.
SEQ P1: DT/XY/Ctrls 1–6: Controllers Setup
[Track01...16, Master Track]
[040.00...300.00, EXT]
[Off, ..., After Touch Lock]
[Toggle, Momentary]
1–6
Menu
[Off, On]
221