069: Tape Echo Bpm - Korg M3 Parameter Manual

069: Tape Echo BPM

This is a tape echo that lets you synchronize the delay time
to the tempo of the song.
Wet: Mono In - Stereo Out / Dry: Stereo In - Stereo Out
Left
Feedback
Feedback Amt
Tape
+
Saturation
Trim Pre Tone High / Low Damp
Wah Flatter
Right
BPM
Tempo
Base Note x Times
BPM
D -mod
MIDI syncs to the system
MIDI,
tempo; 40–300 sets the tempo
BPM (Delay) 40.00...
manually for this individual
300.00
a
effect
Tap1 Dmod Selects the modulation source
Off...Tempo
Src of the delay time
Selects the type of notes to
Tap1 Delay
... specify the delay time (tap1)
Note
Sets the number of notes to
b Times x1...x32 specify the delay time (tap1)
Displays an error message
Time Over? ---, OVER! when the delay time exceeds
the upper limit
Selects the note value used to
Tap1 Dmod specify the delay time when the
...
Note modulation is at maximum
c
Specifies the number of notes
used to specify the delay time
Times x1...x32
when the modulation is at
maximum
Sets the position of Tap 2
d Tap2 relative to the Tap 1 delay time
0...100
Position [%] the depth of pitch variation
Sets the position of Tap 3
Tap3 relative to the Tap 1 delay time
e 0...100
Position [%] the depth of pitch variation
Tap1 Level 0...100 Sets the Tap1 output level
Pan L, 1...99, R Sets the stereo image of tap1
f
Sets the Tap1 feedback amount
FB Amt –100...+100
Tap2 Level 0...100 Sets the Tap2 output level
Pan L, 1...99, R Sets the stereo image of tap2
g
Sets the Tap2 feedback amount
FB Amt –100...+100
Tap3 Level 0...100 Sets the Tap3 output level
Pan L, 1...99, R Sets the stereo image of tap3
h
Sets the Tap3 feedback amount
FB Amt –100...+100
Sets the amount of feedback
Feedback 0...100
for Taps 1, 2, and 3
Selects the modulation source
Src Off...Tempo
i of feedback amount
Sets the depth by which
Amt –100...+100 feedback amount will be
modulated
High Damp Sets the damping amount in
0...100
[%] the high range
j
Low Damp Sets the damping amount in
0...100
[%] the low range
k Saturation 0...100 Sets the distortion amount
Input Trim 0...100 Sets the input gain
l
Pre Tone 0...100 Sets the tone of the input
Wow Flutter Sets the frequency at which
0.02...1.00
[Hz] pitch variation will occur
m
Wow Flutter Sets the depth of pitch
0...100
depth variation
Wet / Dry
(3)
(2)
(1)
Level Pan
Delay
Tap2/3 Position
Wet / Dry
Delay Time
p.473
p.485
p.473, p.485
p.473, p.485
p.485
p.485
p.485
p.480
p.480
p.480
p.480
p.480
p.480
Dry, 1 : 99... Sets the balance between the
Wet/Dry
99 : 1, Wet effect and the dry input
Selects a modulation source for
n Src Off...Tempo
Wet/Dry
Sets the modulation amount
Amt –100...+100
for Wet/Dry
a: Tap1 Dmod Src
b: Tap1 Delay Note
b: Times
c: Tap1 Dmod Note
c: Times
If Tap1 Dmod Src is Off or the selected modulation is at 0,
the delay time will be the length specified by Tap1 Delay
Note and Times.
If Tap1 Dmod Src is other than Off, the delay time will
change so that it will be as specified by Tap1 Dmod Note
and Times when the maximum modulation is reached.
b: Time Over?
You can set the delay time up to 5,400msec. If the delay time
exceeds this limit, the error message "OVER!" appears in the
display. Set the delay time parameters so that this message
will not appear. Time Over? is only a display parameter.
Delay
485