166: St/Cross Long Delay; 167: Hold Delay - Korg M3 Parameter Manual

166: St/Cross Long Delay

(Stereo/Cross Long Delay)
This is a stereo delay, and can by used as a cross-feedback
delay effect in which the delay sounds cross over between
left and right by changing the feedback routing. You can set
a maximum of 2,730msec for the delay time.
Stereo In - Stereo Out
Left
High Damp Low Damp
Delay
Input Level D-mod
Stereo/Cross
Feedback
High Damp Low Damp
Input Level D-mod
Delay
Right
Switches between stereo delay
a Stereo/Cross Stereo, Cross
and cross-feedback delay
L Delay Time Sets the delay time for the left
b 0.0...2730.0
[msec] channel
R Delay Time Sets the delay time for the right
c 0.0...2730.0
[msec] channel
Sets the feedback amount for
L Feedback –100...+100
the left channel
Selects the modulation source
d Src Off...Tempo
of feedback amount
Sets the modulation amount of
Amt –100...+100
the left channel feedback
Sets the feedback amount for
R Feedback –100...+100
the right channel
e
Sets the modulation amount of
Amt –100...+100
the right channel feedback
High Damp Sets the damping amount in
f 0...100
[%] the high range
g Low Damp Sets the damping amount in
0...100
[%] the low range
Input Level Sets the modulation amount of
–100...+100
Dmod [%] the input level
h
Selects the modulation source
Src Off...Tempo
for the input level
Sets the width of the stereo
i Spread –50...+50 image of the effect sound
Dry, 1 : 99... Sets the balance between the
Wet/Dry
99 : 1, Wet effect and the dry input
Selects a modulation source for
j Src Off...Tempo
Wet/Dry
Sets the modulation amount
Amt –100...+100
for Wet/Dry
Wet / Dry
Stereo/Cross Spread
Wet / Dry
p.476
p.476
p.472
p.472
p.476

167: Hold Delay

This effect records the input signal and plays it back
repeatedly. You can control the start of recording and reset
via a modulation source. Easy to use for real-time
performances.
Wet: Mono In - Stereo Out / Dry: Stereo In - Stereo Out
Left
+
Delay
Loop Time: Auto/ ...5400ms
Right
D -mod
REC Control
D -mod
RST Control
Sets Automatic loop time setup
Loop Time Auto,
a mode or specifies loop time
[msec] 1...10800
Specifies whether delay time is
Loop BPM
b Off, On set in milliseconds, or as a note
Sync
value relative to tempo
MIDI syncs to the system
MIDI,
tempo; 40–300 sets the tempo
BPM 40.00...
manually for this individual
300.00
effect
c
An error indication that appears
if delay time exceeds the upper
Time Over? ---, OVER!
limit when MIDI/Tempo
Sync=On
Loop Base Selects the type of notes to
...
Note specify the delay time
d
Sets the number of notes to
Times x1...x32
specify the delay time
REC Control Selects control source for
e Off...Tempo
Src recording
RST Control Selects control source for reset
f Off...Tempo
Src
g Manual REC REC Off, Sets the recording switch
Control REC On
h Manual RST
Off, RESET Sets the reset switch
Control
L100...L1, C, Sets the stereo image of the
Pan
R1...R100 effect
Selects the modulation source
i Src Off...Tempo
of stereo image of the effect
Sets the modulation amount of
Amt –100...+100
stereo image of the effect
Dry, 1 : 99... Sets the balance between the
Wet/Dry
99 : 1, Wet effect and the dry input
Selects a modulation source for
j Src Off...Tempo
Wet/Dry
Sets the modulation amount
Amt –100...+100
for Wet/Dry
a: Loop Time [msec]
With Auto, the loop time is automatically set. Otherwise,
you can specify the loop time.
When Auto is selected, the Loop Time is automatically set to
the time it takes for a performance recorded while the
Modulation Source or Manual REC Control is on. However,
if the time length exceeds 10,800msec, the loop time will be
automatically set to 10,800msec.
c: Time Over?
You can set the delay time up to 10,800msec. If the delay
time exceeds this limit, the error message "OVER!" appears
in the display. Set the delay time parameters so that this
message will not appear. Time Over? is only a display
parameter.
Double Size
Wet / Dry
Pan
Wet / Dry
Tempo
BPM
Base Note x Times
BPM
p.521
p.522
p.522
p.522
p.522
p.522
p.522
p.522
p.522
521