9-2: Mfx1; 9-3: Mfx2, 9-4: Tfx - Korg M3 Parameter Manual

Sequencer mode
9–2: MFX1
9–2a
9–2b
Here you can edit the parameters of the effect you selected
for MFX1 in the P9: MFX/TFX– MFX1 page.
9–2a: MFX1
MFX1 On/Off
This turns master effect 1 on/off. This is linked with the on/
off setting in the P9: MFX/TFX– Routing page.
Note: If Control Assign is RT Control, MFX1 On/Off can be
controlled by switch 6. MFX2 and TFX are controlled by
switches 7 and 8, respectively.
Ch (Control Channel)
Specifies the MIDI channel that will control dynamic
modulation (Dmod) for the master effect.
Ch01...Ch16: The specified MIDI channel will be used for
control.
G ch: The global MIDI Channel (Global 1–1a) will be used
for control. Normally you will use the G ch setting.
P (Effect Preset)
[P00, P01...15, U00...15, ---------------]
Effect Presets let you easily store and recall all of the settings
for an individual effect. You can store up to 16 user presets
for each effect type, in addition to 15 re-writable factory
presets.
The same presets appear in all of the modes (Program,
Combination, Sequence, and Sampling).
Note that edits to effects parameters are automatically
stored with the Combination–you don't need to store them
as an Effect Preset. Presets just make it easier to re-use your
favorite settings.
For instance, you can save an Effect Preset while working on
a particular Combination, and then later use the same Effect
Preset in a different Program, Combination, or Song.
P00: Initial Set: These are the default settings that are
recalled when you select an effect type in the P9: MFX/TFX–
Routing page. You can't save your own settings here.
P01...P15: These contain preset data that Korg plans to
provide in the future. We recommend that you store your
settings in U00–U15.
U00...U15: These are areas in which you can store your own
settings.
---------------: This shows that no Effect Preset has been
selected. You'll see this if you've just selected an effect,
written a program, or selected a new Song. Selecting this
setting from the menu will not have any effect.
For more details, please see "Using Effect Presets" on
page 101.
264
MFX1 Parameters
Here you can set the effect parameters of the effect you
chose in the P9: MFX/TFX– Routing page.
9–2
For details on the individual effects, please see the "Effect
Menu
Guide" on page 421.
▼9–2: Menu Command
• 0: Memory Status ☞p.271
• 1: Panel–SW Solo Mode On ☞p.106
• 2: Exclusive Solo ☞p.107
• 3: Copy MFX/TFX ☞p.118
• 4: Swap MFX/TFX ☞p.118
• 5: FF/REW Speed ☞p.272
• 6: Set Location (Set Location for Locate Key) ☞p.272
• 7: Put Effect Setting to Track ☞p.288
For more information, please see "Sequencer: Menu
Command" on page 271.
[Off, On]
9–3: MFX2,
9–4: TFX
These pages let you edit the parameters of Master Effect 2
and the Total Effect. To select different effects types, use the
[Ch01...16, G ch]
P9: MFX/TFX– Routing page.
The parameters of MFX2, TFX are the same as for MFX1. For
more information, please see "9–2: MFX1," above.