182: Ep Cabinet/Drive; 183: St. Mic + Preamp; Preamp); 184: Multitap Cho/Delay (Multitap Chorus/Delay) - Korg Krome Parameter Manual

182: EP Cabinet/Drive

This faithfully simulates the characteristics of the power
amp and speaker cabinet of a famous model of tine‐type
electric piano. It produces a tone with a distinctive sense of
drive and warmth.
Tine EP I,
Select the power amp and
a
Cabinet Type Tine EP II,
speaker cabinet.
Reed EP
Drive Switch Off, On Switches drive on/off
Selects a modulation source to
Src Off...Tempo
b switch drive on/off
Toggle, Sets the switch mode for drive
Sw
Moment on/off modulation
Sets the amount of overdrive
Drive 00.0...100
and distortion in the amp
Selects a modulation source for
c Src Off...Tempo
Drive
Sets the modulation amount for
Amt –100...+100
Drive
Dry,
Sets the balance between the
Wet/Dry 1 : 99...99 : 1,
effect and the dry input
Wet
d Selects a modulation source for
Src Off...Tempo
Wet/Dry
Sets the modulation amount for
Amt –100...+100
Wet/Dry
c: Drive
At lower settings, the amp is very clean; as you increase the
Drive, it gets dirtier and more distorted. The output level is
compensated, so increasing Drive causes only a moderate
increase in perceived volume.
183: St. Mic + PreAmp (Stereo
Mic Modeling + PreAmp)
This is a stereo mic and preamp simulator (See "028: Mic
Model+PreAmp (Mic Modeling + PreAmp)" on page 267.).
For example you might use this to simulate micing of a
stereo source such as a rotary speaker.
Stereo In - Stereo Out
Left
Mic Simulation
Mic Simulation
Right
Wet / Dry
Tube Pre Amp
Output Level
Tube Pre Amp
Wet / Dry
Double Size 182: EP Cabinet/Drive
184: Multitap Cho/Delay
(Multitap Chorus/Delay)
This effect has six chorus blocks with different LFO phases.
You can produce a complex stereo image by setting a
different delay time and depth for each block. You can
control the delay output level via a modulation source.
Wet: Mono In - Stereo Out / Dry: Stereo In - Stereo Out
Left
Feedback
Tap1 Delay
Tap2 Delay
Tap3 Delay
+
Tap4 Delay
Tap5 Delay
Tap6 Delay
Right
0 [degree]
180 [degree]
60 [degree]
240 [degree]
120 [degree]
300 [degree]
LFO: Triangle
D -mod
On/Off Control
LFO
a Frequency 0.02...13.00 Sets the speed of the LFO
[Hz]
Tap1 (000) Sets the Tap1 (LFO phase=0
0...2000
[msec] degrees) delay time
Depth 0...30 Sets the Tap1 chorus depth
Always On,
b
Always Off, Selects on, off, or modulation
OnOff source for the control of Tap1
Status
(Dm), output
OffOn
(Dm)
Tap2 (180) Sets the Tap2 (LFO phase=180
0...2000
[msec] degrees) delay time
Depth 0...30 Sets the Tap2 chorus depth
c
Always On, Selects on, off, or modulation
Always Off, source for the control of Tap2
Status
OnOff (Dm), output
OffOn (Dm)
Tap3 (060) Sets the Tap3 (LFO phase=60
0...2000
[msec] degrees) delay time
Depth 0...30 Sets the Tap3 chorus depth
Always On,
d
Always Off, Selects on, off, or modulation
OnOff source for the control of Tap3
Status
(Dm), output
OffOn
(Dm)
Tap4 (240) Sets the Tap4 (LFO phase=240
0...2000
[msec] degrees) delay time
Depth 0...30 Sets the Tap4 chorus depth
Always On,
e
Always Off, Selects on, off, or modulation
OnOff source for the control of Tap4
Status
(Dm), output
OffOn
(Dm)
Tap5 (120) Sets the Tap5 (LFO phase=120
0...2000
[msec] degrees) delay time
Depth 0...30 Sets the Tap5 chorus depth
Always On,
f
Always Off, Selects on, off, or modulation
OnOff source for the control of Tap5
Status
(Dm), output
OffOn
(Dm)
Tap6 (300) Sets the Tap1 (LFO phase=300
0...2000
[msec] degrees) delay time
Depth 0...30 Sets the Tap6 chorus depth
Always On,
g
Always Off, Selects on, off, or modulation
OnOff source for the control of Tap6
Status
(Dm), output
OffOn
(Dm)
Wet / Dry
Wet / Dry
Panning Preset
p.332
p.332
p.332
p.332
p.332
p.332
331