Sampling P8: Ifx (Insert Effect); 8-1: Routing - Korg M3 Parameter Manual

Sampling P8: IFX (Insert Effect)

Here you can make insert effect settings for use in Sampling
mode.
If you want to apply an insert effect IFX1–5 to the external
audio signal while you sample it, choose IFX1–5 as the Bus
Select (0–2a) parameter for Input1, 2 or S/P DIF L, R, and
adjust the parameters of the insert effect.
If you want to apply effects to a previously-sampled sample
or a sample you loaded, and resample the result, set the P8:
Insert Effect page "Bus Select (All OSCs to)" (8–1b)
parameter to IFX1–5, and adjust the effect settings.
(Resample 0–2b)
For instance, you can:
• Send the output of a multisample to an insert effect
• Route a sound to an insert effect
• Make detailed settings for insert effects
• Make common LFO settings for effects
For details on insertion effects, please see "Effect Guide" on
page 421.
Insert effect settings for Sampling mode will revert to
the default settings when the power is turned off.
Use Copy Insert Effect if you want to keep your insert
effect settings. Select a program or combination, copy
the insert effect settings of Sampling mode, and save
them. Write the program or combination to save it in
internal memory. Then in Sampling mode, use Copy
Insert Effect to load the effect settings from the
program or combination so that they can be used in
Sampling mode.
You can also use the Write FX Preset menu command to
save effects individually.
Sampling P8: IFX (Insert Effect) 8–1: Routing
8–1: Routing
8–1a
8–1b
8–1c
8–1a: Routing Map
This displays the status of the insert effect settings.
This indicates the input buses being sent to the insert effects,
the effects that are assigned, their on/off status, chaining,
and the output bus that follows the insert effect.
Use the P8: IFX– Insert FX Setup page to select insert effects,
turn them on/off, and make chain settings.
8–1b: Bus Select (All OSCs to)
Bus (IFX/Output) Select
[L/R, IFX1...5, 1...4, 1/2, 3/4, Off]
Selects the bus.
If you want to apply an effect to a sample (multisample) that
you sampled or loaded, select IFX1–5. (Resample 0–2b)
Note: After you resample, L/R will automatically be selected
as the Bus (IFX/Output) Select setting. These settings are
made automatically so that the effect will not be applied
again (i.e., a second time) when you play back the sample
that was resampled with the IFX. (In the same way, the on/
off settings for MFX1, 2 and TFX On/Off will also be turned
off.) Be aware of this if you want to sample once again.
FX Control Bus
This sends the output of the oscillator (multisample) to a FX
Control bus (mono 2-channel; FX Ctrl1, 2)
Use the FX Control buses when you want to use a separate
sound to control the input of an effect. You can use the two
(mono 2-channel) buses to control effects freely.
For more information, please see "FX Bus (FX Control Bus)"
on page 305.
AUX Bus
This sends the output of the oscillator (multisample) to the
AUX buses (four mono channels; 1, 2, 3, and 4). If you want
to resample from the AUX buses, set Source Bus to AUX1/2
or AUX3/4.
The AUX buses are internal buses used for sampling etc. in
each mode.
Off: The oscillator output will not be sent to the AUX buses.
Normally you will leave this Off.
1, 2, 3, 4: The oscillator output will be sent in monaural to
the corresponding AUX bus.
1/2, 3/4: The oscillator output will be sent in stereo to the
corresponding pair of AUX buses.
8–1
Menu
[Off, 1, 2]
[Off, 1, 2, 3, 4, 1/2, 3/4]
323