Korg M3 Parameter Manual page 631

3. You can use data increment (CC#96) [Bn, 60, 00] or data
decrement (CC#97) [Bn, 61, 00] (n: channel, value is
fixed at 00) to change the value in steps of one.
The M3 can receive the following three RPN messages
(tuning, transpose, and pitch bend range).
Tuning
RPN fine tune [Bn, 65, 00, 64, 01]
This RPN message can be used to adjust the detuning for a
program or timbre (in Combination mode), or for a track (in
Sequencer mode).
The procedure is as follows.
1. [Bn, 65, 00, 64, 01]: Select RPN parameter 01.
2. [Bn, 06, mm, 26, vv]: Use data entry to set the value. A
value of 8192 [mm, vv=40, 00] is center, 0 [mm, vv=00,
00] is -100 cents, and 16383 [mm, vv=7F, 7F] is +99 cents.
Note: You can use the universal exclusive Fine Tune message
to adjust the overall tuning that corresponds to the Master
Tune (Global P0: 0–1a) parameter. (See "About system
exclusive messages" on page 621)
Transposing
RPN coarse tune [Bn, 65, 00, 64, 02]
This RPN message can be used to adjust the transposition
for a program or timbre (in Combination mode), or for a
track (in Sequencer mode).
The procedure is as follows.
1. [Bn, 65, 00, 64, 02]: Select RPN parameter 02.
2. [Bn, 06, mm, 26, vv]: Use data entry to set the value.
Normally only the upper byte is used.
A value of 8192 [mm, vv=40, 00] is center, 6656 [mm, vv=34,
00] is –12 semitones, and 9728 [mm, vv=4C, 00] is +12
semitones.
Note: You can use the universal exclusive Coarse Tune
message to adjust the overall tuning that corresponds to the
Key Transpose (Global P0: 0–1a) parameter. (See "About
system exclusive messages" on page 621)
Changing the pitch bend range
RPN pitch bend range [Bn, 64, 00, 65, 00]
This RPN message can be used to adjust the pitch bend
range for a program or timbre (in Combination mode) or for
a track (in Sequencer mode).
The procedure is as follows.
1. [Bn, 65, 00, 64, 00]: Select RPN parameter 00.
2. [Bn, 06, mm, 26, vv]: Use data entry to set the value.
Normally only the upper byte is used.
A value of 0 [mm, vv=00, 00] is +00, and a value of 1536
[mm, vv=0C, 00] is +12 (one octave). Although it is possible
to set a negative value for a timbre/track, only positive
values can be set using RPN messages.
About system exclusive messages
Since the way in which these messages are used is left up to
each manufacturer, they are mainly used to transmit and
receive sound data and editing data for parameters that are
unique to a particular instrument. The M3's system
exclusive message format is [F0, 42, 3n, 70, ff, .... F7]
F0: exclusive status
42: Korg ID
3n: [n=0–F] global MIDI channel 1–16
mm: Future model ID (05: M3-61,0E: M3-73, 17: M3-88,
M3-M: 1C)
ff: function ID (type of message)
MIDI applications Messages transmitted and received by the M3
:
:
F7: end of exclusive
Note: To obtain a copy of the "MIDI Implementation" which
includes MIDI System Exclusive format information, please
contact your Korg distributor.
Universal system exclusive
Certain of the system exclusive messages are publicly
defined for a specific use, and these are called universal
system exclusive messages.
The M3 uses the following six universal system exclusive
messages.
Inquiry message request [F0, 7E, nn, 06, 01, F7]
Inquiry message [F0, 7E, nn, 06, 02, (nine bytes), F7]
When an inquiry message request is received, the M3 will
respond by transmitting an inquiry message that means "I
am a Korg M3, with system version ..."
GM system on [F0, 7E, nn, 09, 01, F7]
When this message is received in Sequencer mode, the M3
will be initialized for GM playback.
Master volume [F0, 7F, nn, 04, 01, vv, mm, F7]
(vv: lower byte of the value, mm: upper byte of the value,
together indicating 16384 steps)
This message is transmitted if you assign Master Volume as
the function of the Assignable Pedal or as a Realtime Control
Slider 5–8 and operate the controller. This will adjust the
overall volume balance without changing the relative
volume balance between timbres/tracks. When this
message is received, the result will be the same as when the
controller is operated.
Master balance [F0, 7F, nn, 04, 02, vv, mm, F7]
(vv: lower byte of the value, mm: upper byte of the value,
together indicating 16384 steps, where 8192 is the default
position, and lower values will move the sound toward the
left)
When this is received, the overall panning will be adjusted
without changing the relative panning between timbres/
tracks.
Master fine tuning [F0, 7F, nn, 04, 03, vv, mm, F7]
(A value of 8192 [mm, vv=40, 00] is center, 4096 [mm, vv=20,
00] is –50 cents, and 12288 [mm, vv=60, 00] is +50 cents.)
When this is received, the "Master Tune" (Global P0: 0–1a)
parameter will be set.
Master coarse tuning [F0, 7F, nn, 04, 04, vv, mm, F7]
(Normally only the upper byte mm is used. A value of 8192
[mm, vv=40, 00] is center, 6656 [mm, vv=34, 00] is –12
semitones, and 9728 [mm, vv=4C, 00] is +12 semitones.)
When this is received, the Key Transpose (Global 0–1a)
parameter will be set.
Transmitting sound settings data (Data
Dump)
Data for programs, combinations, drum kits, global settings,
and sequencer data can be transmitted as MIDI System
Exclusive messages. The operation of sending this system
exclusive data to an external device is called a "data dump."
By performing a data dump, you can store the M3's sounds
and settings on an external device, or rewrite the sounds
and settings of another M3.
There are the following two types of data dump.
• When you use the Dump (Global P1) menu command to
dump data, various types of internal memory data will
621