168: Lcr Bpm Long Dly - Korg M3 Parameter Manual

Effect Guide
b: Loop BPM Sync
c: BPM
d: Loop Base Note
d: Times
If Loop BPM Sync is on, the Times setting is ignored; the
loop time is determined by BPM, Loop Base Note, and
Times. Even in this case, the delay time cannot exceed
10,800 msec.
"Hold" procedure (when Loop Time = Auto)
1. "Rec Src" JS +Y: #01
"Reset Src" JS –Y: #02
"Manual REC Control" REC Off
"Manual RST Control" RESET
"Loop Time [msec]" Auto
"MIDI/Tempo Sync" Off
It should be noted that all recordings will be deleted
while Reset is On.
2. "Manual RST Control" Off
Reset is cancelled and the unit enters Rec ready mode.
3. Push the joystick in the +Y direction (forward) and play a
phrase you wish to hold. When you pull the joystick to
its original position, the recording will be finished and
the phrase you just played will be held.
Loop Time is automatically set only for the first recording
after resetting. If the time length exceeds 10,800msec,
Loop Time will be automatically set to 10,800msec. (If
you have set Times to 1–10,800msec, the specified loop
time will be used regardless of the time taken from push-
ing the joystick forward until it is pulled back. However,
the recording method remains the same. The phrase
being played while the joystick is pushed forward will be
held.)
4. If you made a mistake during recording, pull the joystick
in the –Y direction (back) to reset. In this way, the record-
ing will be erased. Repeat step 3. again.
5. The recorded phrase will be repeated again and again.
You can use this to create an accompaniment.
6. By pushing the joystick in the +Y direction (forward),
you can also overdub performances over the phrase that
is being held.
e: REC Control Src
g: Manual REC Control
REC Control Src selects the modulation source that controls
recording.
If this modulation is on, or if Manual REC Control is set to
On, you can record the input signal. If a recording has
already been carried out, additional signals will be
overdubbed.
The effect is off when a value for the modulation source
specified for the REC Control Src parameter is 63 or
smaller, and the effect is on when the value is 64 or
higher.
f: RST Control Src
h: Manual RST Control
The RST Control Src parameter specifies the modulation
source that controls the reset operation.
When you set this modulation source to On, or Manual RST
Control to RESET, you can erase what you recorded. If the
Loop Time parameter has been set to Auto, the loop time is
also reset.
The effect is off when a value for the modulation source
specified for the RST Control Src parameter is 63 or
smaller, and the effect is on when the value is 64 or
higher.
522

168: LCR BPM Long Dly

(L/C/R BPM Long Delay)
The L/C/R delay enables you to match the delay time with
the song tempo.
Wet: Mono In - Stereo Out / Dry: Stereo In - Stereo Out
Left
Input Level D-mod
+
High Damp Low Damp
Input Level D-mod
Right
Tempo
BPM
Base Note x Times
BPM
Base Note x Times
Base Note x Times
MIDI syncs to the system
MIDI,
tempo; 40–300 sets the tempo
BPM 40.00...
manually for this individual
300.00
effect
a
Displays an error message
Time Over? ---, OVER! when the delay time exceeds
the upper limit
Selects the type of notes to
L Delay Base
... specify the delay time for TapL
Note
b Sets the number of notes to
Times x1...x32 specify the delay time for TapL
Level 0...50 Sets the output level of TapL
elects the type of notes to
C Delay Base
... specify the delay time for TapC
Note
c Sets the number of notes to
Times x1...x32 specify the delay time for TapC
Level 0...50 Sets the output level of TapC
Selects the type of notes to
R Delay Base
... specify the delay time for TapR
Note
d Sets the number of notes to
Times x1...x32 specify the delay time for TapR
Level 0...50 Sets the output level of TapR
Feedback Sets the feedback amount of
–100...+100
(C Delay) TapC
Selects the modulation source
e Src Off...Tempo
for the TapC feedback
Sets the modulation amount of
Amt –100...+100
the TapC feedback
High Damp Sets the damping amount in
0...100
[%] the high range
f
Low Damp Sets the damping amount in
0...100
[%] the low range
Input Level Sets the modulation amount of
–100...+100
Dmod [%] the input level
g
Selects the modulation source
Src Off...Tempo
for the input level
Sets the width of the stereo
h Spread 0...50 image of the effect sound
Dry, 1 : 99... Sets the balance between the
Wet/Dry
99 : 1, Wet effect and the dry input
Selects a modulation source for
i Src Off...Tempo
Wet/Dry
Sets the modulation amount
Amt –100...+100
for Wet/Dry
a: Time Over?
You can set the delay time up to 10,920msec. If the delay
time exceeds this limit, the error message "OVER!" appears
in the display. Set the delay time parameters so that this
message will not appear. Time Over? is only a display
parameter.
Wet / Dry
L Delay
Level
C Delay
Spread
Level
Feedback
R Delay
Level
Wet / Dry
p.473
p.522
p.473
p.473
p.473
p.473
p.473
p.473
p.476
p.476
p.472
p.472
p.476