016: Stereo Decimator; 017: St. Analog Record - Korg M3 Parameter Manual

Effect Guide

016: Stereo Decimator

This effect creates a rough sound like a cheap sampler by
lowering the sampling frequency and data bit length. You
can also simulate noise unique to a sampler (aliasing).
Stereo In - Stereo Out
Left
Pre LPF Resolution
D -mod
Sampling Frequency
LFO
Pre LPF Resolution
Right
Pre LPF Off, On
a
High Damp
0...100
[%]
Sampling 1.00k...
Freq [Hz] 48.00k
b Src Off...Tempo
–48.00k...
Amt
+48.00k
LFO
Frequency 0.02...20.00
[Hz]
c
Src Off...Tempo
–20.00...
Amt
+20.00
MIDI Sync Off, On
MIDI,
BPM 40.00...
d
300.00
Base Note ...
Times x1...x32
Individual,
LFO Type Common1,
Common2
e
CmnLFO
–180...+180
Offset [deg]
Depth 0...100
Src Off...Tempo
f
Amt –100...+100
g Resolution 4...24
Output Level 0...100
Src Off...Tempo
h
Amt –100...+100
Dry, 1 : 99...
Wet/Dry
99 : 1, Wet
i Src Off...Tempo
Amt –100...+100
a: Pre LPF
If a sampler with a very low sampling frequency receives
very high-pitched sound that could not be heard during
playback, it could generate pitch noise that is unrelated to
the original sound. Set Pre LPF to On to prevent this noise
from being generated.
452
Wet / Dry
High Damp Output Level
Decimator
Decimator
High Damp Output Level
Wet / Dry
Selects whether the harmonic
noise caused by a decrease in
sampling frequency is
generated or not p.452
Sets the ratio of cut of the high
range
Sets the sampling frequency
Selects the modulation source
of the sampling frequency
Sets the modulation amount of
the sampling frequency
Sets the speed of the LFO
Selects a modulation source for
LFO speed
Sets the modulation amount of
LFO speed
When this is on, the LFO speed
is set by BPM, Base Note, and
Times, instead of Frequency
MIDI syncs to the system
tempo; 40–300 sets the tempo
manually for this individual
effect
Selects the type of notes that
specify the LFO speed
Sets the number of notes that
specify the LFO speed
Selects either (individual) LFO,
Common FX LFO1, or Common
LFO2 p.448
Sets the phase offset when
Type = Common 1 or Common
2 p.448
Sets the depth of the sampling
frequency LFO modulation
Selects the LFO modulation
source of the sampling
frequency
Sets the LFO modulation
amount of the sampling
frequency
Sets the data bit length p.452
Sets the output level p.452
Selects the modulation source
for the output level
Sets the modulation amount of
the output level
Sets the balance between the
effect and the dry input
Selects a modulation source for
Wet/Dry
Sets the modulation amount
for Wet/Dry
If you set the Sampling Freq to about 3 kHz and set Pre LPF
to Off, you can create a sound like a ring modulator.
g: Resolution
h: Output Level
If you set a smaller value for the Resolution parameter, the
sound may be distorted. The volume level may also be
changed. Use Output Level to adjust the level.

017: St. Analog Record

(Stereo Analog Record)
This effect simulates the noise caused by scratches and dust
on analog records. It also reproduces some of the
modulation caused by a warped turntable.
Stereo In - Stereo Out
Left
EQ Trim
Pre EQ
EQ Trim Pre EQ
Right
a Speed [RPM] 33 1/3, 45, 78 Sets the r.p.m. of a record
Sets the modulation depth
b Flutter 0...100
Noise Density 0...100 Sets the noise density
c
Noise Tone 0...100 Sets the noise tone
Noise Level 0...100 Sets the noise level
Selects the modulation source
Src Off...Tempo
d for the noise level
Sets the modulation amount of
Amt –100...+100
the noise level
Sets the click noise level
Click Level 0...100
Selects the modulation source
e Src Off...Tempo
for the click noise level
Sets the modulation amount of
Amt –100...+100
the click noise level
f EQ Trim 0...100 Sets the EQ input level
Pre EQ Cutoff
300...10.00k Sets the EQ center frequency
[Hz]
g
Q 0.5...10.0 Sets the EQ band width
Gain [dB] –18.0...+18.0 Sets the EQ gain
Dry, 1 : 99... Sets the balance between the
Wet/Dry
99 : 1, Wet effect and the dry input
Selects a modulation source for
h Src Off...Tempo
Wet/Dry
Sets the modulation amount
Amt –100...+100
for Wet/Dry
b: Flutter
This parameter enables you to set the depth of the
modulation caused by a warped turntable.
e: Click Level
This parameter enables you to set the level of the click noise
that occurs once every rotation of the turntable. This
simulation reproduces record noise, and the noise generated
after the music on a vinyl record finishes.
Wet / Dry
Analog Record
Simulation
Wet / Dry
p.452
p.452