Korg M3 Parameter Manual page 343

Move 996 to 999
Convert MS To Program
(Convert Multisample To Program)
This command converts the selected multisample into a
program.
If you have recorded a sample or created a multisample and
would like to play it in Program mode, Combination mode,
or Sequencer mode, you must create a program that uses
that multisample for its oscillator.
If you've created a multisample in Sampling mode and want
to use it as a program, go to Prog P2: OSC Pitch and set the
OSC1 Multisample/Wave Sequence and OSC2
Multisample/Wave Sequence Bank parameters (if Type =
Multisample) to RAM Mono or RAM Stereo. A multisample
that you created in Sampling mode can be used in the
program, and then to make program settings to specify how
the multisample will be sounded.
However by executing the Convert MS To Program
command, you can quickly and easily convert the Sampling
mode settings into a new program, without having to make
any Program mode settings as described above.
1. Use Multisample Select (MS) (0–1a) to select the multi-
sample that you want to convert to a program.
2. Select "Convert MS To Program" to open the dialog
box.
3. Press the text edit button to open the text edit dialog
box, and input a new program name (up to 24 charac-
ters).
By default, the multisample name will be specified
automatically.
4. If Use Destination Program Parameters is unchecked:
Executing the command will replace the multisample of the
convert destination program with the multisample selected
here, and will initialize the remaining program parameters.
The multisample will be converted into a program whose
Oscillator Mode (Prog 1–1b) is Single.
If Use Destination Program Parameters is checked:
Executing this command will replace the multisample of the
convert destination program with the multisample selected
here, and will not initialize the remaining program
parameters. Use this setting if you wish to use the parameter
settings of an existing preset program, etc.
If you check Use Destination Program Parameters, be
aware of the following points.
The Oscillator Mode of the convert-destination program
must be Single. If you attempt to execute this command
when these conditions are not satisfied, a message will
Sampling: Menu Command Convert MS To Program (Convert Multisample To Program)
indicate "Oscillator Mode conflicts." You will need to
change the Oscillator Mode setting of the convert
destination program.
5. In To "Program," select the convert destination pro-
gram.
When the edit cell is selected, you can use the numeric keys
0–9, the VALUE dial, the VALUE slider, and q/u switches
to make a selection. When you press the popup button, the
Program Select menu will appear. Here you can select a
program by bank.
It is recommended that you use I–E as the program bank for
Sampling mode.
6. To execute the Convert Multisample To Program com-
mand, press the OK button. To cancel, press the Cancel
button.
MS Mono To Stereo/MS Stereo To Mono
(Change Multisample Type)
This command converts a mono multisample to stereo, or a
stereo multisample to mono. If the selected multisample is
mono, the dialog box will allow you to execute MS Mono To
Stereo. If the selected multisample is stereo, the dialog box
will allow you to execute MS Stereo To Mono.
1. Use Multisample Select (MS) (0–1a) to select the multi-
sample that you want to change to stereo or mono.
2. Choose either "MS Mono To Stereo" or "MS Stereo To
Mono" to open the dialog box.
3. To execute the Change Multisample Type command,
press the OK button. To cancel, press the Cancel button.
When you execute this command, the multisample type and
sample assignment will change as follows.
MS Mono To Stereo
• The selected multisample will be converted to stereo.
The last two characters of the multisample name will be
overwritten as –L.
• An identical multisample will be newly created, but with
the last two characters of the multisample name
overwritten as –R.
• Mono samples assigned to the original multisample will
be assigned to both –L and –R multisamples.
• If samples assigned to the original multisample are part
of a stereo pair of samples, the –L and –R samples will
be assigned to the –L and –R multisamples.
: MS Stereo To Mono
• The selected multisample will be converted to mono.
The –L or –R at the end of the multisample name will be
deleted.
• Multisamples that are stereo pairs of the selected
multisample will be deleted.
333