085: Comp - P4Eq; 086: Comp - Cho/Flng - Korg M3 Parameter Manual

Effect Guide

085: Comp - P4EQ

(Compressor -
Parametric 4-Band EQ)
This effect combines a mono compressor and a four-band
parametric equalizer. You can change the order of the effects.
Wet: Mono In - Mono Out / Dry: Stereo In - Stereo Out
Left
Compressor
+
Right
Envelope - Control
COMPRESSOR
[C]
a 1...100
Sensitivity
[C]Attack 1...100
b
Output Level 0...100
P4EQ
c [E]Trim 0...100
[E]B1 Cutoff
20...1.00k
[Hz]
d
Q 0.5...10.0
Gain [dB] –18...+18
[E]B2 Cutoff
50...5.00k
[Hz]
e
Q 0.5...10.0
Gain [dB] –18...+18
[E]B3 Cutoff
300...10.00k
[Hz]
f
Q 0.5...10.0
Gain [dB] –18...+18
[E]B4 Cutoff
500...20.00k
[Hz]
g
Q 0.5...10.0
Gain [dB] –18...+18
Comp ➝
h Routing P4EQ, P4EQ
➝ Comp
Dry, 1 : 99...
Wet/Dry
99 : 1, Wet
i Src Off...Tempo
Amt –100...+100
492
Routing
Parametric 4Band EQ
Comp
Trim
Output Level
Sets the sensitivity p.441
Sets the attack level p.441
Sets the compressor output
level p.441
Sets the parametric EQ input
level
Sets the center frequency of
Band 1
Sets the bandwidth of Band 1
p.445
Sets the gain of Band 1
Sets the center frequency of
Band 2
Sets the bandwidth of Band 2
p.445
Sets the gain of Band 2
Sets the center frequency of
Band 3
Sets the bandwidth of Band 3
p.445
Sets the gain of Band 3
Sets the center frequency of
Band 4
Sets the bandwidth of Band 4
p.445
Sets the gain of Band 4
Switches the order of the
compressor and parametric EQ
Sets the balance between the
effect and the dry input
Selects a modulation source for
Wet/Dry
Sets the modulation amount
for Wet/Dry

086: Comp - Cho/Flng

(Compressor - Chorus/Flanger)
This effect combines a mono compressor and a chorus/
flanger. You can change the order of the effects.
Wet: Mono In - Stereo Out / Dry: Stereo In - Stereo Out
Left
Wet / Dry
EQ Trim LEQ HEQ
+
Right
Envelope - Control
Wet / Dry
COMPRESSOR
[C]
a
Sensitivity
[C]Attack
b
Output Level 0...100
c [C]EQ Trim
[C]Pre LEQ
Gain [dB]
d
Pre HEQ Gain
[dB]
CHORUS/FLANGER
[F]LFO
Frequency
[Hz]
e
LFO
Waveform
[F]Delay
Time [msec] 0.0...1350.0
f Depth
Feedback
[F]Cho/Flng
Wet/Dry
g
Src
Amt
[F]Output
h
Mode
i Routing
Wet/Dry
j Src
Amt
h: [F]Output Mode
i: Routing
When Wet Invert is selected, the right channel phase of the
chorus/flanger effect sound is inverted. This creates
pseudo-stereo effects and adds spread.
However, if a mono-input type effect is connected after this
effect, the left and right sounds may cancel each other,
eliminating the chorus/flanger effects.
When Routing is set to Flanger→Comp, [F]Output Mode
will be set to Normal.
Routing
Compressor Chorus/Flanger
Comp Chorus/Flanger
Output Level
Feedback
Cho/Flng Wet / Dry
LFO: Tri / Sine
1...100 Sets the sensitivity
1...100 Sets the attack level
Sets the compressor output
level
0...100 Sets the EQ input level
–15...+15 Sets the gain of Low EQ
–15...+15 Sets the gain of High EQ
0.02...20.00 Sets the speed of the LFO
Triangle,
Selects the LFO Waveform
Sine
Sets the delay time
Sets the depth of LFO
0...100
modulation
Sets the feedback amount
–100...+100
–Wet... Sets the effect balance of the
–1 : 99, Dry, chorus/flanger
1 : 99...Wet
Selects the Wet/Dry
Off...Tempo modulation source for the
chorus/flanger
Sets the Wet/Dry modulation
–100...+100
amount for the chorus/flanger
Normal, Selects the output mode for the
Wet Invert chorus/flanger
Comp ➝
Switches the order of the
Flanger,
compressor and chorus/flanger
Flanger ➝
Comp
Dry, 1 : 99... Sets the balance between the
99 : 1, Wet effect and the dry input
Selects a modulation source for
Off...Tempo
Wet/Dry
Sets the modulation amount
–100...+100
for Wet/Dry
Wet / Dry
Normal
+ Output Mode
–
Wet Invert
Wet / Dry
p.441
p.441
p.441
p.461
p.450, p.461
p.492
p.492